Aspöck Systems TPMS Montageanleitung
Vorschau ausblenden
Andere Handbücher für TPMS:
- Montageanleitung (14 Seiten) ,
- Betriebsanleitung (58 Seiten) ,
- Betriebsanleitung (76 Seiten)
Quicklinks
Verwandte Anleitungen für Aspöck Systems TPMS
Inhaltszusammenfassung für Aspöck Systems TPMS
- Seite 1 ASPÖCK TPMS SENSOR MONTAGEANLEITUNG MOUNTING INSTRUCTION aspoeck.com INSTRUCTION...
- Seite 2 No modifications may be made to the product unless only the original spare parts intended for this purpose or spare parts approved by Aspöck are used and installed by professionally qualified personnel. Product liabilities are limited in item 9 of the GTCs. www.aspoeck.com/en/top/downloads • ASPÖCK TPMS SENSOR MONTAGEANLEITUNG | MOUNTING INSTRUCTION...
- Seite 3 - Foreign objects are visible in the pressure opening - The battery life of the internal sensor is expired! • Use the correct valve for the rim. • Only use original Aspöck TPMS fastening screws and only for one installation process. ASPÖCK TPMS SENSOR MONTAGEANLEITUNG | MOUNTING INSTRUCTION...
- Seite 4 6.0 Nm ±0.5 Nm festziehen. Press and hold the sensor against the rim as shown in the previous image. Tighten the T30 screw with a calibrated torque screwdriver to 6.0 Nm ±0.5 Nm. ASPÖCK TPMS SENSOR MONTAGEANLEITUNG | MOUNTING INSTRUCTION...
- Seite 5 Now fit the tyre in accordance with the tyre changer manufac- ensure that the beads are in the correct position. turer‘s instructions so that the upper bead is fitted over the rim flange. ASPÖCK TPMS SENSOR MONTAGEANLEITUNG | MOUNTING INSTRUCTION...
- Seite 6 Fill the tyre according to the manufacturer‘s instructions and Turn the rim clockwise and ensure that the sensor has not been ensure that the beads are in the correct position. pinched during the installation process. ASPÖCK TPMS SENSOR MONTAGEANLEITUNG | MOUNTING INSTRUCTION...
- Seite 7 The screw must be replaced with a new screw each time the sensor is removed from the rim. If the valve on the rim is not replaced, the valve thread must be cleaned to remove any resi- due or contamination in the thread. ASPÖCK TPMS SENSOR MONTAGEANLEITUNG | MOUNTING INSTRUCTION...
- Seite 8 The screw must be replaced with a new screw each time the sensor is removed from the rim. If the valve on the rim is not replaced, the valve thread must be cleaned to remove any resi- due or contamination in the thread. ASPÖCK TPMS SENSOR MONTAGEANLEITUNG | MOUNTING INSTRUCTION...
- Seite 9 3. 40 rpm (±10%) to 5 Nm (±0.5 Nm) 4. 50 ms stop 5. 25 rpm (±10%) to 6 Nm (±0.5 Nm) Anzugsmoment 6 Nm 5 Nm 1.5 Nm Zeit 30 rpm 300 rpm 40 rpm 25 rpm ASPÖCK TPMS SENSOR MONTAGEANLEITUNG | MOUNTING INSTRUCTION...
- Seite 10 ASPÖCK Systems GmbH Enzing 4, 4722 Peuerbach, AUSTRIA aspoeck.com Office: +43 7276 2670-0 E-Mail: office@aspoeck.com Bei Nichteinhaltung dieser Montageanleitung erlischt die Gewährleistung! Non-compliance with this mounting instruction will void the warranty! GREAT BRITAIN, IRELAND FRANCE, LUXEMBOURG SPAIN, SWEDEN, FINLAND, NORWAY, DEN- ITALY ALGERIA, MOROCCO, TUNISIA PORTUGAL...