Aspöck Systems TPMS Montageanleitung
Vorschau ausblenden
Andere Handbücher für TPMS:
- Montageanleitung (10 Seiten) ,
- Betriebsanleitung (58 Seiten) ,
- Betriebsanleitung (76 Seiten)
Quicklinks
Verwandte Anleitungen für Aspöck Systems TPMS
Inhaltszusammenfassung für Aspöck Systems TPMS
- Seite 1 ASPÖCK TPMS SENSOR MONTAGEANLEITUNG MOUNTING INSTRUCTION aspoeck.com INSTRUCTION...
-
Seite 2: Service-Hinweise
Other (limiting) liability provisions can be found in item 11 of the Terms of Sales and Delivery (TSD) www.aspoeck.com . • Limiting product liability provisions are laid down in item 12 of the Terms of Sales and Delivery (TSD) www.aspoeck.com . ASPÖCK TPMS SENSOR MONTAGEANLEITUNG | MOUNTING INSTRUCTION... - Seite 3 - Foreign objects are visible in the pressure opening - The battery life of the internal sensor is expired! • Use the correct valve for the rim. • Only use original Aspöck TPMS fastening screws and only for one installation process. ASPÖCK TPMS SENSOR MONTAGEANLEITUNG | MOUNTING INSTRUCTION...
- Seite 4 6.0 Nm ±0.5 Nm festziehen. Press and hold the sensor against the rim as shown in the previous image. Tighten the T30 screw with a calibrated torque screw- driver to 6.0 Nm ±0.5 Nm. ASPÖCK TPMS SENSOR MONTAGEANLEITUNG | MOUNTING INSTRUCTION...
- Seite 5 Now fit the tyre in accordance with the tyre changer ma- ensure that the beads are in the correct position. nufacturer‘s instructions so that the upper bead is fitted over the rim flange. ASPÖCK TPMS SENSOR MONTAGEANLEITUNG | MOUNTING INSTRUCTION...
- Seite 6 Fill the tyre according to the manufacturer‘s instructions and wurde. ensure that the beads are in the correct position. Turn the rim clockwise and ensure that the sensor has not been pinched during the installation process. ASPÖCK TPMS SENSOR MONTAGEANLEITUNG | MOUNTING INSTRUCTION...
- Seite 7 The screw must be replaced with a new screw each time the sensor is removed from the rim. If the valve on the rim is not replaced, the valve thread must be cleaned to remove any residue or contamination in the thread. ASPÖCK TPMS SENSOR MONTAGEANLEITUNG | MOUNTING INSTRUCTION...
- Seite 8 The screw must be replaced with a new screw each time the sensor is removed from the rim. If the valve on the rim is not replaced, the valve thread must be cleaned to remove any residue or contamination in the thread. ASPÖCK TPMS SENSOR MONTAGEANLEITUNG | MOUNTING INSTRUCTION...
- Seite 9 40 rpm (±10%) to 5 Nm (±0.5 Nm) 50 ms stop 25 rpm (±10%) to 6 Nm (±0.5 Nm) Anzugsmoment 6 Nm 5 Nm 1.5 Nm Zeit 30 rpm 300 rpm 40 rpm 25 rpm ASPÖCK TPMS SENSOR MONTAGEANLEITUNG | MOUNTING INSTRUCTION...
- Seite 10 Route the free end of the strap through the other end strap in the dropwell (lowest point) of the rim. of the cradle to form a loop, ensuring the strap is not twisted. ASPÖCK TPMS SENSOR MONTAGEANLEITUNG | MOUNTING INSTRUCTION...
- Seite 11 * Note: Procedure may vary depending on Tyre Machine type. It is imperative to ensure the tyre bead does not contact the cradle during fitment as this may result in movement or damage of the cradle and/or sensor! ASPÖCK TPMS SENSOR MONTAGEANLEITUNG...
- Seite 12 *Note: Procedure may vary depending on Tyre Machine type. It is imperative to ensure the tyre bead does not contact the cradle during fitment as this may result in movement or damage of the cradle and/or sensor! ASPÖCK TPMS SENSOR MONTAGEANLEITUNG...
- Seite 13 **Note: Procedure may vary depending on Tyre Machine type. It is imperative to ensure that no contact occurs between the tyre and cradle during fitment as this may result in damage of the cradle and/or sensor. ASPÖCK TPMS SENSOR MONTAGEANLEITUNG...
- Seite 14 ASPÖCK Systems GmbH aspoeck.com Enzing 4, 4722 Peuerbach, AUSTRIA Office: +43 7276 2670-0 E-Mail: office@aspoeck.com...