Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENG
Instruction Manual EASYLITE
1.
Use as directed:
This product serves exclusively lighting purposes and may:
only be used with a voltage of 230V ~50Hz.
not be exposed to strong mechanical loads or to strong
contamination.
only be installed and operated after a condition inspection if the
product is dirty or has been moistened through storage.
not be modified or converted.
If these points named above are not adhered to, a short circuit or
electrical shock may occur!
2.
Technical Data:
230505/15
Operating voltage:
pri. 230V ~50Hz sek. 12V
Safety class:
Safety type:
IP44
Bulb:
QR51, GU5.3, max.
50W
Dimensions (H/Head-
Spot: 20,5/10
Ø):
Display: 89,5/10
Swivel range:
160°
Weight:
1,75 kg
Importer:
SLV Elektronik GmbH
IP 44: Protection against foreign objects > Ø 1,0mm - Protection against
splashing water from all directions.
3.
Installation
The electric connection may be executed only by an electric expert
who is familiar with the valid directives!
Attention: Switch off the power of the mains supply line or
respectively of the connection lead before doing any works
Use only parts, which are supplied with the product or are described as
accessories! Otherwise the product or the installation might not be
sufficiently safe.
Installation place:
The product is suited for wall, ceiling and floor installation.
Make sure that the product is mounted on a stable, even and tilt-fixed
background.
The light exit should be placed at least so far from the illuminated surface,
as indicated as minimum distance on the type label of the luminaire. Pay
special caution to easily inflammable objects (e.g. foliage).
Separate Installation Steps
Remove the mounting plate from the base of the lamp (1).
Carefully penetrate the pre-punched holes. SPOT: Do not apply this step
when using the earth spike. The may not be penetrated.
Determine the place of installation and mark the holes to be drilled. Note
that the cable outlet of the power supply line fits between the mounting
bracket and the canopy. Do not damage the power supply line, e.g. by
drilling, screws or strong bending.
Electrical Connection
The product must be able to be separated by an all pole separation from
the current supply.
Direct the connection lead through the cable screwing (2).
Secure the cable screwing.
For electric connection attach the black or brown wire (live conductor) of
the mains supply with the clamp L and the blue wire (neutral conductor)
of the mains supply with the clamp N. The green-yellow wire (protective
conductor) of the mains supply has to be tightly screwed into the earth
of the product.
clamp
Now fasten the basis back on the mounting plate.
Fasten the mounting plate to the mounting surface (3).
Inserting the bulb (4): Loosen the two screws on the font of the
lamphead. Carefully take off the front part and the glass. Take care that
the glass does not fall down. MR16(QR51): Use the supplied sucker to
stick the bulb into the socket. QRB111(QR-LP): Take out the retaining
spring. Screw the contacts tightly on the bulb. Direct the bulb into the
lamphead. Secure the bulb with the retaining spring. Put the glass and
the front part of the lamphead back on.
voltage installations! Check all electrical connections once in a
while for a secure fit. Otherwise there is risk of fire.
Ensure that the light fixture holds securely!
Adjust the direction of the lamp head by loosening the adjustment
screw(A).
The product is now ready for operation.
230555/65
I
QRB111
QR-LP111, G53, max.
50W
Spot: 23,5/15,5
Display: 92,5/15,5
2,25
.
4.
Operation
Information for the user:
Operate the product only if it is working correctly. Switch off the product
with a malfunction immediately and operate it again only after examination
by an electrical specialist. This is the case, when:
visible damages appear.
the product does not work.
smoke, steam or crackling sounds appear.
an overheating is recognisable.
Repairs of the product or work on mains voltage-prominent sections may
only be carried out by qualified electricians.
Attention: Here exists mortal danger from an electric shock!
How to avoid failure and fire risk:
Do not cover the product - provide free air circulation!
Do not hang or fasten anything on the product, especially no decoration.
Replace damaged protection glasses immediately!
Never let children play unsupervised with electric products! Children
can not always estimate dangers in dealing with electric energy correctly.
High currents with low-
MR16
:
The following enviromental influences may have unwanted effects on
the surface of the product:
acid rain and sour soil
high salt content in the air
thawing salt
cleaning agents
other chemical substances (e.g. herbicides)
Protect the product by adequate means to avoid unwanted changes of the
surface. Cleaning tip: Switch off power! Clean the product with a damp
cloth.
What is to do if a bulb is defect or does not work?
Disconnect the product from power, before you exchange the bulbs.
Caution: Let the bulb cool down first before replacement – otherwise
considerable risk of injury exists because of the hot surface.
Replace the bulbs only with bulbs of the same data like socket, power
and capacity. Every other sort of bulb can lead to damages of the light.
Replacing the bulb: see Installation.
5.
What else has to be considered?
Disconnect the product from power, before you...
clean or maintain the product.
do any works on the product or its components (electric expert).
12/2006 © by SLV Elektronik GmbH
230505/15/55/65
Technical Details are subject to change.
Duplication prohibited !
F
Mode d'emploi EASYLITE
1.
A utiliser comme indiqué :
Ce produit ne sert qu'à éclairer:
il est prévu pour une tension de 230V ~50Hz.
il ne doit être soumis ni aux efforts mécaniques importants ni à un
encrassement important.
il ne doit être utilisé qu'après examen si le produit a été stocké dans un
entrepôt humide ou sale.
il ne doit pas être modifié.
Un non-respect de ces points peut causer un court-circuit ou une
décharge électrique!
2.
Informations techniques:
230505/15
Tension
pri. 230V ~50Hz sek. 12V
d'alimentation:
Classe de protection:
Degré de protection:
IP44
Ampoule:
QR51, GU5.3, max.
50W
Dimensions (H/tête-
Spot: 20,5/10
Ø):
Display: 89,5/10
Portée d'inclinaison:
160°
Poids:
1,75 kg
Importateur:
SLV Elektronik GmbH
IP 44: Protection contre les corps étrangers durs > Ø 1,0 mm - Protection
contre les éclaboussures provenant de toutes les direction.
3.
Installation
La connection électrique doit être exécutée par un professionnel,
lequel est familier des normes en vigueur!
Attention: Mettez l'alimentation électrique ou le raccordement au
secteur hors tension avant de travailler!
230555/65
I
QR-LP111, G53, max.
50W
Spot: 23,5/15,5
Display: 92,5/15,5
2,25
Werbung
