HIKVISION DS-KB8113-IME1 Kurzanleitung

DS-KB8113-IME1
Vandal-Resistant Doorbell
UD18946B
E N G L I S H
Diagram References
Appearance
1
Low Illumination Supplement Light
1 Microphone 2 Built-in Camera 3
Call Button
4 5 Loudspeaker
Note: The appearance of the device vary according to different model. Refers to the actual device.
Terminal
2
12 VDC: 12 VDC Power Supply Input
1 A1 AI: Alarm Input
2 LAN: Network Interface (PoE Supported) A2 GND: Grounding
B1 COM: Common Interface
NO: Door Lock Relay Output (Connect Electric Strike)
B2
B3 NC: Door Lock Relay Output (Connect Electric Bolt or Magnetic Lock)
Note: Wiring description refers to the User Manual.
Installation
3
Before you begin:
Make sure the device in the package is in good condition and all the assembly parts are
included.
The device supports two ways of power supply: 12 VDC, or PoE power supply. Please
make sure your power supply matches your doorbell.
Make sure all the related equipment is power-off during the installation.
Make sure the wall is strong enough to withstand 4 times the weight of the doorbell.
Check the product specification for the installation environment.
Mounting Accessories
To install the doorbell onto the wall, you are required to use a matched mounting plate.
Wall Mounting
1. Fix the wall mounting plate to the wall with 4 expansion screws.
2. Insert terminal blocks into interfaces of the doorbell body, and connect the network
cable.
3. Fix the doorbell body to the protective shield tightly.
4. Hook the doorbell to the wall mounting plate tightly.
5. Use the set screw to secure the doorbell with the mounting plate.
Configuration
4
Set Up Mobile Client
1
Before you begin:
Make sure your mobile device has been connected to Wi-Fi.
1. Install Hik-Connect client and register a user account for iOS and Android.
1) Search Hik-Connect in App Store or Hikvision website to download and install the
client.
2) Launch the App and follow the on-screen instructions to register a user account.
2. Start the client, and login the client.
2 Set Up Doorbell via Client
To operate the doorbell normally, you should add the doorbell to the client.
1. On the home page of the client, tap Add Device.
- Scan QR Code of the doorbell to add.
Note: The QR Code is printed on the label, which is on the rear panel of doorbell. If you
have already installed the device, you can scan the QR code in the user manual.
- Tap Image icon to select QR code picture to add.
- Tap Edit icon to enter Serial No. of the doorbell to add.
2. Tap Next. Connect the device to a router with a network cable, and tap Connected.
Note: Make sure your mobile device is connected to the same router.
3. The account is connected to the device.
Set Up Doorbell via Indoor Station
3
1. Choose Language and tap Next.
2. Set network parameters and tap Next.
- Edit Local IP, Subnet Mask and Gateway parameters.
- Enable DHCP, the device will get network parameters automatically.
3. Configure the indoor station and tap Next.
a. Select Indoor Station Type.
b. Edit Floor and Room No.
4. Linked related devices and tap Next. If the device and the indoor station are in the
same LAN, the device will be displayed in the list. Tap the device or enter the serial No.
to link.
a. Tap the doorbell in the list to link.
b. Tap the settings icon to pop up the Network Settings page.
c. Edit the network parameters of the doorbell manually or enable DHCP to get the
network parameters automatically.
d. Optional: Enable Synchronize Language to synchronize the Language of doorbell
with indoor station.
e. Tap OK to save the settings.
5. Tap Finish to save the settings.
Remote Operation
4
a Live View via Mobile Client
Tap the doorbell in the list to open the floating windows. And then tap the floating
window to enter the Live View page.
Tap the video on the screen, you can tap to capture the screen.
Tap to record.
b Two-Way Audio
Call from client software: On the Live View page, tap to create a call between the
client and the device.
Receive call from the device:
You can receive or decline the call from device.
- Tap to receive the call.
- Tap to decline the call.
- Tap to unlock the door remotely.
- Tap to adjust the volume.
- When you communtication with the device, you can tap to mute.
Call indoor station: Press call button to create a call between the indoor station and the
doorbell.
Unlock Remotely via Mobile Client
c
On the main page or on the live view page, tap to unlock the door.
Refer to Video Intercom Vandal-Resistant Doorbell User Manual (scan the QR code) for details.
1
1
2
3
4
5
3.1
44
Unit:mm
3
Protective Shield
Doorbell
Main Body
Hangzhou Hikvision Digital Technology CO.,Ltd. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China
2
3.2
1
Wall Mounting Plate
4
Hooks
1 2
A1
IN
DC 12V
AI G COM NO NC
+ -
LAN
POWER
2
Expansion Screws
Network Interface
Power Interface
Terminal Blocks
5
Set Screw
Rubber Plug
A2 B1 B3
OUT
ALARM
Alarm Interface
Network Cable