Werbung
Verfügbare Sprachen
Verfügbare Sprachen
RULES FOR SAFE DRIVING
For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds.
• Only for 12 and 24 Volt vehicles: in first gear the
vehicle has a differential effect like a real motor
vehicle; on smooth terrain and with just one child
on board, the two wheels can turn at different
speeds and they can slip and slow down.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.
CUSTOMER SERVICE
offers an after-sales assistance service,
PEG PEREGO
directly or through a network of authorized
assistance centres, for any repairs or replacements
and the sale of original spare parts. To contact the
assistance centres refer to the "Assistance Centres"
booklet included in the packaging.
The item's serial number must always be quoted.
See the page on spare parts to find out how to
identify the serial number.
Peg Perego always strive to best satisfy their
customers' needs. Knowing the opinions of our
customers is therefore very important and valuable
to us. We would be very grateful if, once you have
used the product, you would fill out the
which you can find on
SATISFACTION QUESTIONNAIRE
the internet at: www.pegperego.com, making
any observations or suggestions you might have.
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
1 • Clip the rear mudguard into place by inserting
the 3 tabs in the slots in the bodywork shown by
the arrows.
2 • Turn the body work upside down and attach the
mudguard to it by pressing it, making sure the
centre tab is inserted first (A).
• Repeat steps 1 and 2 on the other side.
3 • Insert the handle in the hole in the bodywork (1)
and turn it downwards (2). PLEASE NOTE: The
two handles are different. Position them with the
flat side facing the saddle.
4 • Turn the bodywork over to access the underside
and attach the handle with the screw provided.
• Repeat steps 3 and 4 with the other handle.
5 • Place bushing A on one of the two wheels with
only one hubcap, lining the 4 pins up with the
holes.
6 • Insert the long metal axle into the wheel.
7 • Slide a washer onto the axle.
8 • Insert the axle with the wheel and washer in the
hole on the right hand side of the bodywork, as
shown in the figure.
9 • Place the remaining bushing (B) on the other
wheel with only one hubcap.
10 • Insert the wheel on the axle on the left hand
side of the bodywork, making sure the wheel
bushing is properly fitted into the pentagon on
the trike.
11 • Place the red tool on one of the two ends of the
axle.
12 • Turn over the bodywork, keeping the red tool
underneath.
13 • Insert a stud in the black tool.
14 • Put it on the other end of the axle as shown in
the figure and use a hammer to secure the wheel
with the stud.
• Turn the trike over and repeat the procedure to
secure the other wheel.
15 • Look closely at the handlebar tubes to ensure
they are fitted properly. The left hand tube
(marked SX) has two holes in the upper section,
unlike the right hand one (marked DX).
16 • Insert the right tube in the right hand side of the
front section, as shown in the figure.
17 • Secure it with the screw provided.
• Repeat steps 16 and 17 with the left tube.
18 • Insert the front mudguard onto the handlebar
tubes, positioning it as shown in the figure.
PLEASE NOTE: The mudguard is fitted with two
tabs that prevent it from being fully attached if it
is inserted incorrectly.
19 • Insert the caps in the handlebar tubes,
positioning them as shown in figure A.
20 • Insert the wheel between the tubes and line up
all the holes. Insert the short metal axle.
21 • Put the red tool in place and turn over the entire
handlebar unit, keeping the red tool underneath.
• Insert a stud in the black tool and secure the
wheel as shown in the figure.
• Turn the handlebar unit onto the other side and
repeat the procedure to secure the wheel there
too.
22 • Attach the nut provided under the front section.
23 • Attach the handlebar unit to the bodywork,
ensuring that the clip locks into place in the part
below the front section (see the details in the
following picture).
24 • The clip has to lock into the curved slot, as
shown in detail in the figure (A: view from above
- B: view from below).
25 • Attach the tank cover by clipping into place the 3
tabs in the bodywork, as shown in the figure.
26 • Insert the threaded pin.
27 • Fasten the threaded pin to attach the handlebar
unit to the bodywork, holding the nut under the
front section still with the other hand.
28 • Insert the hand guard marked DX on the right
handlebar tube and the hand guard marked SX
on the left handlebar tube. The picture shows
how to fit the hand guard marked SX.
29 • Secure the hand guards with the screws
provided.
30 • Wet the inside of the rubber grip to make it
CONSUMER
easier to slide onto the handlebar tube. The
rubber grips are identical and can go on the right
or left side.
31 • Clip the headlight into place, pressing first on the
ASSEMBLY
upper part and then on the lower part.
32 • Insert the windshield into the upper part of the
front section.
33 • Press the windshield against the front section in
the points shown in the figure.
34 • Attach the windshield with the two screws
provided.
35 • Connect the electrical system plug to the
battery.
36 • Insert the front part of the saddle in the
bodywork (1), then pull it down (2).
37 • Push the locking clip all the way down in the
hole at the rear of the saddle.
38 • Turn the locking clip to position B to secure the
saddle.
FEATURES AND USE OF THE VEHICLE
39 • The vehicle is ready for use. With both hands on
the handlebar, press the accelerator pedal with
your foot.
REPLACING THE BATTERY
PLEASE NOTE: THE PICTURES OF THE BATTERIES
ARE FOR ILLUSTRATIVE PURPOSES ONLY. YOUR
BATTERY MAY BE DIFFERENT FROM THE MODEL
SHOWN. THIS DOES NOT AFFECT THE
REPLACEMENT AND CHARGING PROCEDURES
DESCRIBED.
40 • Turn the locking clip to position A to release the
saddle. Remove the saddle.
41 • Disconnect the electrical system plug from the
battery.
42 • Unfasten the screw on the battery holder.
Remove the battery holder.
43 • Replace the flat battery with another battery
that has been charged for at least 14 hours.
PLEASE NOTE: Replacement batteries are only
sold with electrical power of 6V/8Ah. This does
not affect the operation of the vehicle.
44 • Replace the battery holder and secure it with
the screw. Reconnect the plugs. Replace the
saddle and turn the locking clip to position B.
• WARNING: After working inside the battery
compartment, always remember to secure the
components with the screw and clip.
CHARGING THE BATTERY
WARNING: BATTERY CHARGING AND ANY
OTHER WORK ON THE ELECTRICAL SYSTEM
MUST BE CARRIED OUT BY ADULTS.
THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
45 • Disconnect plug A of the electrical system from
the battery plug B by pressing the sides.
46 • Plug the battery charger into a domestic power
supply, following the instructions provided with
it. Connect plug B to the battery charger plug C.
47 • When charging is complete, unplug the battery
charger from the domestic socket and then
disconnect plug C from plug B.
48 • Push plug B into plug A until it clicks into place.
After completing the procedure, always
remember to replace and secure the saddle.
Werbung
