Werbung
Verfügbare Sprachen
Verfügbare Sprachen
right
the
guide ® simply
Set
paper
Put
the
power switch ©
oroe
Place
a sheet
of
paper
the
handle ® towards
loading
Pull
paper
starting
position.
proper
Push the loading handle to
">
Press the
ON-LINE key
Notes
to
a sheet
shift
Ifyou
1.
want
process as
described
loading
Make
that
the paper
sure
Ifthe left-hand
guide
2.
paper
sheet
be
will
approx.
1
The two
of
the paper
3.
rollers
the
the edges
width
third
from
of
the tractor
unit ©
Mounting
is
See
the
to
that
a.
it
power
b. Remove the printer cover
the
handle ® towards
loading
Pull
c.
paper
the paper
Now
install
can
you
on
Insert the
d.
hooks
either
platen-unit ®.
of
rear
Push
the
tractor
the
Open both tractor covers
into
the
the
Insert
paper
"zorg
printer
Tum
on.
your
the
First
push
loading
paper
transported automatically
the paper
Leave
loading
j.
another
10
cm
(4
paper
the
Then move
loading
k.
paper
|
Adjust the tractors to correspond exactiy
the
over
m. Carefully
lay
paper
the
tractor covers again.
close
shelf
Now mount
the
n.
paper
shelf.)
paper
0. Put
the
printer cover back onto
Now transport
the paper
p.
sheet appears
the
above
press the
ON-LINE
q. Finally
Note: Make
sure that
your
ADJUSTING THE
print
can be
head
adjusted
The
right-hand side.
When shipped
the
from
factory,
want to
one
or
more copies,
print
printing
single copies
When
and
tear
printer.
on
wear
your
the
to
by sliding
it
The
POWER
on.
green
ON
shelf,
the
on
between
paper
and the
you
then start
will
(The printing
the
and
the
rear again
is
and
for
printer
ready
your
it
after
has
been loaded,
of paper
since
the paper
above,
in
the
straight
remains
printer.
has
set
been
to
leftmost
its
inch.
be set to the
should never
bail
®.
and
inserting fan-fold paper.
tumed
off.
shelf.
and the
paper
you.
feed tractor onto the platen:
side
unit
the
of
tractor
into
so the
down
spring loaded hooks
unit
@.
loosely, as
far
as
printer
it
to
rear,
then
handle
the
above the
until
appears
it
its
handle
front position! Tum
in
inches).
handle to
its
rear position.
the
with
the
so the
tractors
pins
it
again and
horizontal position
in
put
the
printer.
feed
the
by turming
paper
head.
print
is
and
printer
key
ready
your
is
set
to the proper paper
printer
PRINT HEAD
the
head adjustment
with
print
is
lever
to
set at
a position
the
can increase the force
you
to
recommended
reset
is
it
right,
left
as
or
required.
the
indicator
will
light
up.
the
paper
guides.
will
automatically
paper
the
the
inch
from
of
top
1
®
set.
bail
paper
will
action.
easily
do so
you
can
held loosely
is only
by
the
left-hand margin
position,
of
the
outer
edges
the
the openings at
front,
into
@
click
go ®.
will
and the paper
forward again
pull
it
head.
print
the paper
knob clockwise to transport the
width
the
of
paper
are using.
you
into
the sprockets
engage
(Fold the
@.
knob clockwise
the perforation
until
for
action.
length!
(See
®
lever.
find
You
will
for
straight
meant
the
lever
by moving
to
lever
its original
position to
the
be
the
transported to
sheet.)
after completing the
friction
mechanism.
the
the
of
printed
but
one
approx.
paper
side
the
on
of
either
position.
be
will
of
the
®. Then
paper
the
flat
support
against
the second
of
DIP-switch
setting,
page
the
the
inside
printer on
it
If
without
printing
copy.
you
® towards
you.
avoid
unnecessary
5.)
Werbung
