Intex 57190NP Swim Center Family Lounge Bedienungsanleitung Seite 3

(300) EN16927 INFLATABLE POOLS AND PLAY CENTER ITEMS 4.875" X 6.3" 06/11/2020
ENGLISH
• Do not use the mini-pool when using alcohol or medication that may impair your ability to safely use the pool.
• When pool covers are used, remove them completely from the water surface before entering the pool.
• Replace water regularly according to manufacturer recommendations and, depending on hygienic conditions, its
cleanliness, its clarity, and its odour, or if any debris or stains are present in the mini-pool. Use of chemicals in
mini-pools without water circulation may result in direct contact with the chemicals or in areas of high chemical concentration
resulting in injury to the users.
• If chemicals are occasionally used to reduce the frequency of water replacement, follow chemicals manufacturer instructions
closely (especially never use more than recommended), assure the appropriate mixing of chemicals to avoid possible
personal injuries and store chemicals out of reach of children.
• The use and installation of any electrical appliances around mini-pools shall be in accordance with the national regulations.
• Where applicable, remove any means of access from the mini-pool and store it out of reach of children whenever the mini-pool
is not in use.
• Use of accessories not approved by the mini-pool manufacturer (e.g. ladders, covers, pumps, etc.) may result in risks of injuries
or property damages.
• Keep all electrical lines, radios, speakers and other electrical appliances away from the pool. Do not place pool near or under
overhead electrical lines.
• Observe and follow the warnings and safety signs on the pool wall.
General:
• Pool and pool accessories are to be assembled and disassembled by adults only. No tools are required for the assembly.
• Do not set up the pool on a slope or inclined surfaces. The area where the pool is to be set up must be absolutely flat and
level, and at least 2 m away from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry
lines or electrical wires.
• The pool location must allow constant supervision of children in or around the pool.
• The area shall facilitate drainage of the pool water after each use and/or for long term pool storage.
• Do not install the pool on mud, sand, soft or loose soil condition, deck, platform, balcony, concrete, asphalt or any other hard
surfaces.
• Do not lean, straddle, or exert pressure on the inflatable wall or side wall as injury or flooding could occur. Do not allow anyone
to sit on, climb, or straddle the sides of the pool.
• Protect all pool occupants from recreational water illnesses by keeping the pool water clean. Don't swallow the pool water.
Practice good hygiene.
• Remove all hard, sharp and loose objects such as jewelries, watches, buckles, keys, shoes, hairpin, etc from users before
entering the pool.
• Pools are subject to wear and deterioration. Properly maintain your pool. Certain types of excessive or accelerated deterioration
can lead to pool failure. Pool failure might cause large quantities of water to release from the pool.
• Do not modify this product and/or use accessories not supplied by the manufacturer. There are no serviceable parts.
Set up:
Depending on the size of the product, 2 or more adults are recommended for setup. Set up time may vary from 10 to 20 minutes
excluding water fill time.
1. Find a flat, level lawn surface that is free and clear of stones, branches or other sharp objects that may puncture the pool liner or
cause injury. Certain types of grass such as St. Augustine and Bermuda, may grow through the liner. Grass growing through the
liner it is not a manufacture defect.
2. Move the product (in its package) to the selected site before inflating – do not inflate the product and drag it since it may result in
leaks or damage.
3. Slowly unfold the product and inspect the product for rips, tears or punctures. Do not use if the product is damaged.
4. Lay the pool out as evenly as possible and close all drain plugs and/or exhaust valve caps if any.
5. Inflate the bottom air chamber first with a manual air pump designed specifically for inflatable products, and then the next
chamber or chambers in sequence.
6. Fill the product and component such as arch or canopy (if included) with air until the surface is firm to the touch but not hard.
If there is any straining at the seams, the product is over-inflated. If any seam begins to strain, immediately stop the inflation and
release air to reduce the pressure until signs of stress on the seam are gone. Do not over-inflate or use high pressure air
compressor since it may result in seam leaks.
7. Close and recess all inflation valve cap(s) securely by pushing down firmly on it.
SAVE THESE INSTRUCTIONS
Page 2
300