Herunterladen Diese Seite drucken

JVC L-L1 Bedienungsanleitung Seite 6

Werbung

DESCRIPTION
AND FUNCTIONS
@ POWER switch
ON
(-m):
Press to set to this position to
turn
the power
on; the
indicators
and
the
lamp
for the
size detection
sensor
(QL-L2 only) will light.
STAND
BY ( g.): Press to set to this posi-
tion to turn the power off,
Note:
Even
when
the POWER
switch
is off, this
turntable consumes a smal! amount
of elec-
tricity
(2.5 watts).
Disconnect
the
power
cord to turn the electricity off completely.
@ REPEAT button
Press
this button
to repeat
a record, The
REPEAT
indicator will light. To release this
function, press it again; the indicator will go
out,
© Tonearm movement control (< , >)
<_:
Press this arrow to move the tonearm to
the left, the tonearm stops when the but-
ton is released,
>
: Press this arrow to move the tonearm to
the
right,
the
tonearm
stops when
the
button is released,
@ UP/DOWN & START/STOP button
UP/DOWN:
Press this side to lift or lower
the tonearm.
Use this for manual! opera-
tion or when
you
want
to stop playing
temporarily
in the
middle
of a record.
When
playing
records
manually,
move
the
tonearm
to the
required
position
using
the tonearm
movement
control,
then press this button to lower the tone-
arm,
START/STOP:
Press this side to play a re-
cord or to stop the playing of the record.
When this is pressed to start the playing
a record, it acts as the start button and
when
this is pressed
while
a record
is
being played, it acts as the stop button,
Note:
eWhen
using the UP/DOWN
& START/
STOP button or the < , > button, be sure
to press one end of the button.
@ SPEED button (L-L1 only)
Set this button
according
to the speed of
the
record.
The
corresponding
speed
indi-
BESCHREIBUNG
UND FUNKTIONEN
© Netzschalter (POWER)
ON
(-=): Durch Driicken dieses Schalters
wird das Gerat eingeschaltet, die Anzei-
gen und die Lampe fur den Schallplatten-
groRe-Sensor (nur QL-L2) leuchten.
STAND
BY ( 1): Durch nochmaliges Drik-
ken dieses Schalters wird das Gerat abge-
schaltet.
Hinweis:
*
Auch
wenn
der
Netzschalter
ausgeschaltet
ist, nimmt
der
Plattenspieler
eine geringe
Leistung auf (2,5 Watt). Ziehen Sie das Netz-
kabel aus der Steckdose, um die Spannungs-
versorgung ganz auszuschalten.
@ Wiederholungstaste (REPEAT)
Drucken
Sie diese Taste,
um
eine Schall-
platte zu wiederholen, Die
REPEAT-Anzeige
feuchtet.
Durch
nochmaliges
Drucken
der
Taste wird diese
Funktion
wieder
freigege-
ben, die Anzeige erlischt.
@ Tonarmtaste (< , >)
<
: Durch Driicken dieses Pfeils bewegt sich
der Tonarm
nach Jinks und stoppt, wenn
die Taste losgelassen wird,
>
: Durch Drucken dieses Pfeils bewegt sich
der
Tonarm
nach
rechts
und
stoppt,
wenn die Taste losgelassen wird,
O Heben/Senken- und Start/Stop-Taste
(UP/DOWN und START/STOP)
UP/DOWN:
Durch
Driicken
dieser
Seite
hebt oder
senkt sich der Tonarm.
Ver-
wenden Sie diese Funktion beim manuel-
len Betrieb
oder
um
die Wiedergabe
in
der Mitte einer Schallplatte kurzzeitig zu
unterbrechen,
Fir manuellen Betrieb be-
wegen
Sie den
Tonarm
durch Drucken
der Tonarmtaste zur gewunschten Stelle
und driicken
dann
diese Taste, um
den
Tonarm zu senken,
START/STOP:
Diese Seite zum Starten und
Stoppen
der Wiedergabe
drucken, Diese
Seite der Taste wirkt als Starttaste, wenn
der
Plattenspieler
steht,
und
als Stop-
taste, wenn er lauft.
Hinweis:
®Bei den UP/DOWN
& START/STOP- und
<, > -Tasten
immer
auf eine Seite der
Taste driicken,
Fig. 6
cator will light.
eRe
@ SIZE button (L-L1 only)
© Geschwindigkeitstaste (SPEED) (nur L-L1)
tet,
© GréRentaste (SIZE) (nur L-L1)
Stellen
Sie
diese
Taste
entsprechend
der
Schallplattengro&e
ein, Die zugehdrige Gro-
Renanzeige leuchtet.

Werbung

loading

Diese Anleitung auch für:

Ql-l2