Sthor 78854 Bedienungsanleitung Seite 13

GB
TOOL HANDLING
Before starting the work make sure that the housing and connecting cable with a plug are not damaged. Should any damage was
found, it is forbidden to continue the work.
Preparation to work
Warning! All actions associated with fi xing and replacing of accessories, and adjustment of rotational speed etc. should be car-
ried out with the power supply off , so prior to these actions: Pull out the plug of power cable from the mains socket!
Assembly of agitator (II)
Tighten the agitator's tip using spanners for mixer's spindle. The connector to be tighten fi rmly to prevent its spontaneous discon-
nection during operation.
Adjustment of rotational speed (III)
Warning! Due to the fact that the rotational speed control knob is placed on the product's switch, it may lead to accidental start of
the product during the adjustment. That is why the adjustment should be done with power cord plug disconnected from a mains
socket.
The mixer is fi tted with smooth rotation adjustment within range specifi ed in the table with technical data. Rotational speed should
be selected depending on the type of material to be mixed. Rotational speed should be lowered along with increase in density of
mass. It is required to observe the mass that is being mixed during the work and change the speed to avoid mass sloshing. If you
are not sure about the mass density, begin mixing at the lowest rotational speed and increase it gradually.
The adjustment of rotational speed is done by turning a knob placed on the product's switch. Direction marked with the thicker part
of arrow indicates rotational speed increase. Turning in opposite direction lowers the rotational speed.
Starting and stopping the mixer
Note! Prior to each start of operation, make a trial start for approx. 30 seconds. Trial start should be done without agitator sub-
mersed in the mass to be mixed. During trial start, please observe the operation of the agitator and the mixer. Proper work may
be started provided no symptoms of improper operation such as e.g. excessive oscillations, excessive noise or queer odour were
found during the trial start-up.
Use agitators appropriate for the specifi c job. Make sure that the swindle is not bent.
Take on working clothes as well as eye and ear protectors, and other personal safety equipment required when working with
particular material.
Make sure, that the switch of the tool remains in "off " position, insert the plug of mixer's power cable to mains socket.
Grab both mixer's grip handles with your hands.
Adopt a fi rm and stable posture.
Immerse the agitator in product to be mixed. Agitator's head should stay completely under the surface of the liquid being mixed.
This will prevent sloshing of liquid being mixed.
Turn on the mixer by pressing on the electric switch with a fi nger.
Mixer's switching off takes place after release of pressure on switch button.
In the event of long lasting operation you may use the switch lock. To enable the lock press the switch button and switch lock at
the same time. To release the lock press the switch button.
During the work avoid hitting the agitator against walls and bottom of container in which mixing is being carried out. Do not lean
the agitator against bottom of container. Do not keep the agitator in one position, displace it within the container, this will ensure
more homogenous and faster mixing.
Note! If any suspicious noise, crackles, odour, etc. were observed, immediately switch off the mixer and pull the plug out of the
mains.
Mixer maintenance
It is recommended to carry out maintenance of the agitator immediately after the work. This will prevent residues of mass being
mixed from drying on the agitator or its swindle.
Prior to agitator cleaning, it should be dismantled from the mixer. The agitator to be cleaned using solvent for particular substance
that has been mixed. After the cleaning, solvent's residues should be washed away with water and then the agitator should be
thoroughly dried out. While cleaning, use personal safety equipment relevant for work with particular substance. Carefully read
instructions attached to this substance.
Additional notes
Do not overload the tool, temperature of outside surfaces can never exceed 60 °C.
After completed work, turn off the mixer, unplug the tool from the mains socket and carry out the maintenance and inspection.
Declared total value of vibration was measured by means of standardized test method and can be used to compare one tool with
O R I G I N A L I N S T R U C T I O N S
13