Werbung
Verfügbare Sprachen
Verfügbare Sprachen
REF. 60010
EN
INSTRUCTION MANUAL
PRODUCT'S PRESENTATION
This tool has been designed to carry out cutting tasks in
different materials such as wood, steel, plastic and metal.
It features 4 pendulum action positions: 3 orbital cutting ac-
tions and 1 straight cutting action, which allows to adapt the
blade cutting speed according to the material hardness. This
saw also has a bevel angle from 0º to 45º to the left and right
to make angular cuts, a toolless collet sleeve for a quick bla-
de insertion and removal, a LED work light for an improved
working area visibility during operation, a dust blowing sys-
tem, an aluminum alloy base, and a trigger switch lock-off
button to prevent an accidental starting of the tool.
Besides, it includes a wood blade, a parallel guide, and a
dust pipe for the dust chute where to connect a vacuum
cleaner or hose for dust extraction.
SAFETY INSTRUCTRIONS
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions listed below
may result in electric shock, fire and/or serious injury.
• Check for breakage of parts, damage to switches and
any other conditions that may affect its operation.
• Do not operate the tool in the presence of flammable
liquids, gases or dust.
• Dress properly. Do not wear loose clothing or jewelry
and tighten long hair.
• Avoid an accidental starting. Disconnect the battery
from the tool and place the switch in the locked or off
position before making any adjustments, changing ac-
cessories, or storing the tool.
• Keep the tool and its handle dry, clean and free from
oil and grease.
• Always wear eye and respiratory protection.
• Hold the tool by the insulated grip surface when perfor-
ming an operation where the tool may come in contact
with the hidden wiring. Contact with a "live" wire will
make exposed metal parts of the tool "live" and shock
the operator.
• Make sure all keys and adjusting wrenches are remo-
ved from the tool before switching it on to avoid them to
fly away at high velocity.
• Keep your second hand on the auxiliary handle or mo-
tor housing, and keep them away from the cutting area
and blade.
• Do not start the saw with the blade touching any surfa-
ce and wait until the blade reaches its full speed.
• Allow the tool to come to a complete stop before putting
it down.
• Always stand to one side when operating the saw and
allow the blade to come to rest naturally.
ASSEMBLY
Installing and removing saw blades
This saw is equipped with a collet that allows a fast and
convenient blade changing:
1. Lift the transparent blade cover and hold it.
2. Pull the lever of the blade clamp and slide the saw bla-
de into the groove as far as it will go with the blade
teeth pointing forward.
3. Once the lug of the blade is correctly and firmly fitted
into the blade clamp, release the blade clamp lever.
4. Place the transparent blade cover to initial position.
NOTE! You can lightly pull the blade outwards to make sure
it is locked in place.
Installing the dust tube
1. Align the tube with the dust chute placed at the rear
of the jig saw.
2. Insert the tube onto the dust chute.
Installing the parallel guide
1. Loosen the edge guide locking knob.
2. Slide the parallel guide through the slots in the shoe
and adjust to the desired width.
3. Tighten the edge guide locking knob to secure it in po-
sition.
OPERATION
Switching On/Off
To turn it on, push the safety lock to either side of the tool
and depress the trigger switch.
To turn it off, fully release the trigger switch.
NOTE! The trigger switch of this tool features a variable
speed control. By slowly depressing the trigger switch, the
tool will be turned on and will run from slow to fast.
NOTE! The power light lights up when the trigger switch is
slightly or completely pressed.
Angle cutting adjustment
1. Set the shoe adjustment lever to the right and then
push the base plate backwards or forwards until the
body of the saw can freely move in the slot of the base.
2. Move the body of the saw to the left or right and tilt it to
the desired angle from 0º to 45º.
3. Return the shoe adjustment lever to its original position
and check whether the base plate is locked.
Dust blower knob
This jig saw comes with a dust
blower to remove the dust depo-
sited into the workpiece while in
use:
To turn it on, turn the dust blowing
switch to the "ON" positon.
· 5 ·
Werbung
