Werbung
A: ON (.2)......... The sound can be heard through
the speakers which are connect-
éd to the A spedker terminals.
B: ON (.2)......... The sound can be heard through
the speakers which are connect-
ed to the B speaker terminalis.
A:
ON (2)
B: ON (.o)......... The sound can be heard through
the speakers which are connect-
ed to both A and B speaker ter-
minals.
NOTE:
@ When 8 ohms speakers are connected to both A
and B speaker terminals, and the Speakers switch
@ is set at A on, B on, the combined impedance of
the speakers is only 4 ohms.
Avoid using this ar-
rangement.
Be sure to connect speakers of more
than 16 ohms when two sets of speakers are to be
operated simultaneously.
@ Even when the Speaker switch is set to ON ( «= )
with the protection circuit activated, sound cannot
be heard.
@ Bass control
Turning this control to the right from "O" position
increases the bass and conversely, turning it to the
left decreases the bass.
@® Treble control
Turning this control to the right from "O" position
increases the treble and conversely, turning it to
the left decreases the treble.
© Tone switch
Set this switch to ON ( =
) when
adjusting the
sound quality and then proceed to adjust the bass
and treble.
When the switch is set to DEFEAT ( I ), a flat fre-
quency
response
is achieved
regardless
of the
bass and treble adjustment.
@ Balance control
This adjusts the balance of right and left channel
levels.
Loudness switch
Due to the characteristics of human
hearing, the
bass and treble seem to drop off when the sound
volume is decreased.
In order to compensate for
this, push this switch to ON ( «= ), and the bass
and treble will then be emphasized
by +6 dB at
100 Hz and +3 dB at 10 kHz respectively.
@ Subsonic-filter switch
When this switch is set to the 30 Hz ( «= ) posi-
tion, low frequency
noise which
is generated
by
warps in the discs is cut out. It is wise to keep this
switch at the 30 Hz ( «= ) position since it is effec-
tive in cutting out low frequency noise outside the
range of hearing which can adversely affect the
speakers (-6 dB/oct).
@ Mode switch
Set this switch to MONO
( .
) when
playing a
monophonic disc or listening to an FM program in
monophonic.
@) Function switches
These are used to select the program source.
PHONO............ For listening
to discs
on
the
turntable connected to the Pho-
no input jacks @
CD icccinivoctin
For
listening
to
a
program
source
on
a component
con-
nected to the CD input jacks @.
TUNER....:..00068 For listening to a broadcast on
the tuner connected to the Tun-
er input jacks @.
AUX
0. eee
For listening to a program source
on a component
connected
to
the AUX-1 input jacks @)
NOTE:
Press at the center of the switch.
@ Tape select switch
For playing back a tape or recording monitoring,
press the switch Tape-1 ( 11 ) or Tape-2( =
). At
this
time,
set
the
tape
monitor
switch
to
ON { = ).
@® Tape copy switch (Copy 1 > 2)
Dubbing from tape deck 1 to tape deck 2 is possi-
ble by depressing
this switch.
In this case, set
tape deck 1 for playback and tape deck 2 for
recording.
@ Tape copy indicator
When the Tape copy switch @ is depressed, this
indicator lights and tapes can now be copied.
@® Tape monitor switch
For playing back a tape in the tape decks, connect-
ed to the TAPE-1 jacks or TAPE-2 jacks, or for re-
cording monitoring.
(Refer to the section on the
tape select switch @,)
,
a
46 Tape monitor indicator
The Tape monitor indicator indicates that the tape
deck connected to the TAPE-1 (or TAPE-2) jacks is
in playback or monitoring recording mode.
@ Function indicators
This indicates the program source which has been
selected by the Function switches @.
@® Volume control
Use this to adjust the sound volume.
Set the Vol-
ume
control to its leftmost
position
("O") when
switching the power on and off in order to protect
the speaker.
@® Ground terminal
'@ Phono input jacks
@ CD input jacks
@ Tuner input jacks
@ AUX-1 input jacks
@ AUX-2 input jacks
@® Tape-1 rec jacks
@) Tape-1
play jacks
@ Tape-2 rec jacks
@ Tape-2 play jacks
'@ Speakers terminals
@) Power supply cord
——
Multi voltage unit ——_
@ Fuse holder
@) Voltage selector
@ AC outlet
Enalich
Werbung
