Vatos YD-218 Gebrauchsanleitung Seite 2

NOTE:
(1) If the indicator on the remote control keeps flashing when maneuvering the
power controller, this indicates that the batteries are low; they must be replaced.
(2) When done charging, please pull out the charger.
(3) Other USB power sources include LCD TV, DVD, cell phone, etc.
3,Operating helicopter
Install and connect the battery in the helicopter. The indicator lights on the top of the helicopter will flash.
Then turn on the remote, pull the throttle stick to the highest point and then to the lowest to connect with
the helicopter. When the color lights on the circuit board keep lighting, this indicates the frequency is
successfully matched.
---Put the helicopter on the floor with the tail facing the pilot.
---Press the one key take-off/landing to start flying.
1. Going up and going down
Slowly push up the throttle stick, and the rotor
will spin faster and faster. When pulling down
the throttle stick, the helicopter will gradually
land on the floor. If it spins in the air, press the
opposite direction trimmer to stable the
helicopter.
.
3. Flying forward
Pull the thorttle stick up, and the heli
flies forward.
NOTE: When operating the heli to fly forward or backward, it might spin; the trimmer
can be used to adjust the direction.
1. If the heli spins in the air even without touching the throttle stick, the trimmer on the
remote can be adjusted till the heli is stabilized.
2. If the heli spins counter-clockwise, turn the trimmer clockwise to stabilize it.
Spinning counter-clockwise
2. Turning left and right
Turn the throttle stick to right, and the heli
flies right.
Turn the throttle stick to left, and the heli
flies left.
4. Flying backward
Pull the thorttle stick down, and the
heli flies backward.
Right Trimmer
3
3. If the heli spins clockwise, turn the trimmer counter-clockwise to stabilize it.
Spinning clockwise
4、Operation instructions:
1. Turn the helicopter power on; the red indicator flashes meaning it is ready to fly.
2. Turn the remote on and the light on it flashes. This indicates that the throttle is locked
in protect mode. Pull the throttle to the highest point and then to the lowest to unlock.
3. Locking function: In any situation of falling off or crashing, the power in the helicopter
will be turned off automatically. To unlock it, pull the throttle to the highest point and
then to the lowest; this protects the motor and receiver board from over-heating.
4. Heli battery over-discharging protection: The heli descends as the power gets lower.
When the power is below 3.0 V, the power is turned off automatically so the heli will
not crash on the floor due to low power. This helpsto protect the battery and extends
its life span, and makes the battery longer lasting and more powerful.
Operation tip
*Do not fly the heli in direct sunshine or strong light; this affects the flight.
*Do not cover the transmitting light on the remote; this affects infrared signal emitting.
*Do not paste any paper on the heli; this affects infrared signal receiving.
*Do not use other USB chargers to charge the heli.
*Do not mix new and old batteries in the remote.
*Do not mix chargeable and nonchargeable batteries in the remote.
Flying environment
*Indoor with smooth air flow. Note: cold air flow from AC etc affects flight.
*Open area. It is suggested that you fly the heli in an area at least
6 feet (width) *9 feet (length)*3 feet (height).
*Safe area. It is strongly recommended that you fly the heli in an area with no AC,
fans, lamps or hazardous objects, etc.
The heli comes with built-in Li-Poly batter; please note below:
-Do not put the heli in a high temperature environment, such as flame or
electronic heating device or the batter will explode or be damaged.
-Do not put the heli under water or operate and store in a moist environment.
The heli must be kept in a dry environment.
-Do not leave the heli unattended when charging.
-Do not charge the heli on flammable objects such as carpet.
4
Left Trimmer