Operation; Multi Function Keys - Team CB3215 Bedienungsanleitung

English
On/Off
To power-on the radio, press the on/off key POW (1). The TEAM logo appears in the display, and
a beep tone is audible (if activated), before the radio switches to operation mode.
To power-down the radio, hold the on/off key POW (1) until the TEAM logo appears in the display.
When setup in a vehicle, the feature AOP allows the radio to power on automatically once
the battery circuit is closed by the ignition.
Volume
To set the volume level, push the multi function button (PF1-6) that is assiged to volume con-
trol VOL. At the bottom of the display, the symbol VOL:X (X = the current volume level) will
appear. Select the desired value (1-56) with the channel selectors of the microphone or the
rotary channel selector (10) of the radio. Confirm your selection by pressing the PTT key /
rotary channel selector or wait for approximately 5 seconds for automatic confirmation.
Mute
To mute the speaker in operation mode, push the on/off key POW (1) shortly. At the bottom
of the display, the symbol AUDIO:MT (mute) will be visible for a few seconds.
To unmute the radio, push the on/off key POW (1) again. The display will show AUDIO:Esc
(escape).
Note: the signal is not completely muted but extremely reduced.
Channel Selection
For channel selection use the microphone's channel selectors UP/DN or the radio's rotary
channel selector (10).
To fast forward for channel selection, hold the channel selector keys UP/DN. To skip 10 chan-
nels at a time, push the rotary channel selector (10) shortly.
Transmit
For voice signal transmission, push the PTT key and talk, at a moderate volume level, into
the connected microphone at a distance of approximately 10 cm.
The red transmission symbol T appears and the s-meter displays the signal strength at the
upper scale, indicated by the red symbol P.
Reception
The received signal is broadcased through the speaker. The signal strength is displayed on
the upper scale of the s-meter, indicated by the red symbol S.
In the lower section of the display, the settings for volume (VOL), squelch (ASQ or SQL), RF-
Gain (RFG) and high frequency filter (HIC) are visible.
Please note when using the optional CTCSS/DCS feature: if the CTCSS/DCS function is
activated, the incoming signal will only be audible if the CTCSS/DCS codes of transmitter
and receiver match.
Squelch
Two kind of squelch types are available, the manual squelch SQL and the automatic squelch
ASQ. Both squelch types can be adjusted at the radio. For the manual squelch SQL, the set-
tings Off/1-28 are available. For the automatic squelch ASQ, the available levels are 1-9.
Keylock
Activate the key lock by pushing the rotary channel selector (10) until Key Lock appears in
red letters at the bottom of the display. All keys, except the PTT key, are blocked. The symbol
will disappear after 5 seconds and will reappear once a button has been pressed.
To deacitvate the key lock, press the rotary channel seletor until Key Unlock appears in white
letters at the bottom of the display.
22

OPERATION

MULTI FUNCTION KEYS

The Expert-1 is has 6 triple-state function keys. With these 6 multi function keys, 18 different
functions are available. To switch between the 3 sets of functions, use the FUNC key (8).
In the following, the different functions are listed. Please note:
> The multi function key preset can be changed, either manually at the radio or via software
programming with the optional software T-UP36.
> To switch between the 3 different functions per key, use the FUNC key (8).
> To activate the function press the function key.
> Make your selection with the channel selection, i.e. either the UP/DN keys of the microphone
or the the rotary channel selector of the radio.
> Confirm your selection with the FUNC key (8) or wait for approximately 5 seconds until the
radio automatically returns to operation mode.
PF1
MOD (frequency mode - AM/FM)
Switches between the frequency modes AM and FM, if the selected frequency norm offers
both selections. The according Symbol (AM/FM) appears in the display.
Note for frequency norm U (UK): the UK frequencies (FM only) are indicated by the letters
UK, for the EU frequencies (AM/FM) the symbol U is used.
POW (tx-power selection)
This feature is only available in the ham version. In the cb version the message ERROR
is displayed in red letters.
It switches between the selections Low (4 W), Middle (8 W) and High (15 W).
NB (noise blanker)
Activates/deactivates the feature noise blanker (NB). If activated, the symbol NB will be
visible in the display. It reduces the interference of some short peak noises, e.g. car ignition.
PF2
RFG (sensitivy of received signal)
Reduces the signal strength of the received signal. This is helpful, if the signal is too strong
and, therefore, distorted.
Settings: OFF / 3-30 in 3-steps / AUTO.
Please note that the features RF-Gain and squelch directly affect each other.
DSP (channel/frequency mode)
Switches between frequency display mode (XX.XXX with the channel number indication
Cxx) and channel display mode (CH-XX).
RB (Roger Tone)
Activates/deactivates the roger tone feature and switches between the different roger tones.
Via software, a maximum of 8 different roger tones can be programmed. Each tone se-
quence can be composed of a maximum of fourteen tones. The frequency (400-2550
MHz), the duration (10-2550 ms), the pauses between the tones and the number of repe-
titions can also be set.
PF3
EMG (priority channel 1/2)
Repeatedly pushing the function key, will switch from the actual channel to the priority
channel 1, to the priority channel 2 and back to the actual channel. With the priority chan-
nels 1 and 2, the red symbol EMG appears in the display.
By default, EMG 1 is assigned to channel 9 and EMG 2 to channel 19. This can be
changed via software programming.
English
23