Werbung
Verfügbare Sprachen
Verfügbare Sprachen
5.1 Assembling the equipment
Fitting the wheels (Fig. 4-11/13)
Place a split pin for fi tting the wheels (31) through
the appropriate hole in the axle (33) and fi t a
washer (30), a wheel (13) and a washer to the
axle (33) (Fig. 5-6). Now slide the axle (33)
through the guides provided for it on the undersi-
de of the tank (10) (Fig. 7). Fit a washer and the
second wheel (13) to the empty end of the axle
(33) and secure it with the other washer (30) and
the split pin (31) (Fig. 8-10). Push the covers (32)
on to the outside of the wheels (13) so that the
detents engage on the covers (32) for the wheel
(13). (Fig. 11)
Fitting the castors (Fig. 12/12)
Fit the castors (12) into the appropriate moun-
tings on the underside of the tank (10). Push the
castors (12) fi rmly into the mounting until they
engage with a clicking noise (Fig. 12).
Fitting the wire bracket for winding up the
cable an suction hose (Fig. 13/2)
Fit the wire bracket for winding up the cable and
suction hose as shown in Fig. 13. After use, the
cable and the suction hose can be wound onto
the wire bracket.
Fitting the appliance head (Fig. 14-15/5)
The appliance head (5) is fastened to the contai-
ner (10) by the locking hook (18). To remove the
appliance head (5), open the locking hook (18)
and remove the appliance head (5). When fi tting
the appliance head (5), make sure that the lo-
cking hook (18) locks into place correctly.
5.2 Fitting the fi lter
Notice!
Never use the wet and dry vacuum cleaner wit-
hout a fi lter.
Check that the fi lter is securely fi tted at all times.
Fitting the foam fi lter (Fig. 16/25)
For wet vacuuming, slip the supplied foam fi lter
(25) over the fi lter basket (Fig. 2/20). The pleated
fi lter (Fig.3/24) already fi tted upon delivery is not
suitable for wet vacuuming.
Fitting the pleated fi lter (Fig. 17/24)
For dry-vacuuming, slip the pleated fi lter (Fig.
3/24) over the fi lter basket (Fig. 2/20). The pleated
fi lter (Fig. 3/24) is suitable for dry-vacuuming only.
Anl_H_NT_30_Inox_SPK7.indb 17
Anl_H_NT_30_Inox_SPK7.indb 17
GB
5.3 Fitting the tank bag (Fig. 3/35)
Fit the dirt bag (Fig. 3/27) as shown in Figure 18.
5.4 Fitting the suction hose (Fig. 1-3/18)
Connect the suction hose (9) to the correspon-
ding connector on the wet and dry vacuum clea-
ner, depending on the application required.
Vacuuming
Connect the suction hose (9) to the suction hose
connector (8).
Blowing
Connect the suction hose (9) to the blow connec-
tor (19).
Air regulator (Fig. 3/29)
The air regulator (29) can be fi tted between the
suction hose (9) and the suction tube (17). The
suction power of the nozzle can be infi nitely ad-
justed using the air regulator (29).
When wet vacuuming, make selective use of the
air regulator to suck in air as well as liquids. This
will help to take some strain off the equipment
when vacuuming liquids.
5.5 Suction nozzles
Dual-purpose nozzle (Fig. 3/14)
The dual-purpose nozzle (14) is for vacuuming
solids and liquids over medium to large areas.
Various attachments can be fi tted to the combi-
nation nozzle depending on what you sort of work
you wish to carry out:
Crevice nozzle (Fig. 3/23)
The crevice nozzle (23) is designed for vacu-
uming solids and liquids in corners, edges and
other areas that are diffi cult to access.
Upholstery nozzle (Fig. 3)
The upholstery nozzle (26) is specially designed
for vacuuming solids on upholstery and carpets.
6. Operation
6.1 ON/OFF switch (Fig. 1/7)
Switch position 0:
Switch position I:
Switch position AUTO:
6.2 Dry vacuuming
Use the pleated fi lter (24) for dry vacuuming (see
- 17 -
Off
Normal operation
Automatic mode
19.02.2018 14:47:09
19.02.2018 14:47:09
Werbung
