Herunterladen Diese Seite drucken

Sygonix 2918268 Bedienungsanleitung Seite 4

Pir-bewegungsmelder 360 ip54

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

8. Attach the front cover and secure it with the screw on the underside.
7 Operation
Important:
After connecting the sensor to the power, wait at least 2 minutes before making adjust-
ments. The sensor needs some time to adjust to the environment.
7.1 Switch-on time "TIME"
Control how long the connected the load stays ON after
the sensor is triggered.
Rotate the dial to adjust the time.
If new motion is detected during the switched-on time, the
timer will restart.
See section "Technical data, PIR sensor time delay".
7.2 Switching threshold "LUX"
You can adjust the switching threshold for different ambi-
ent light levels.
Turn the dial to make adjustments. The higher the number
the higher the ambient light level under which the sensor is
triggered.
Note: To test the sensor in daylight, set it to the highest bright-
ness level.
8 Cleaning and care
Important:
– Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions.
They damage the housing and can cause the product to malfunction.
– Do not immerse the product in water.
1. Clean the product with a dry, fibre-free cloth.
9 Troubleshooting
Problem
Possible causes
Connected load does
Check the LUX setting, it should correspond to ambient
not switch ON.
light levels. E.g., if it is set too high the sensor will not trig-
ger in the dark.
Check the power supply is functioning correctly.
Check if the connected device (e.g., lamp) is functioning
correctly.
Movements within the detection area are too rapid and are
filtered out by the electronic system to prevent switching er-
rors.
Motion detection is
The ambient temperature is too high.
not functioning cor-
There are obstructions preventing the sensor from detect-
rectly.
ing heat sources (e.g., glass).
Check that if there are induction sources within detection
area.
Observe the correct installation height. See section "Tech-
nical data" for further information.
The connected load is
Constant movements are occurring within the detection
always ON.
area.
New movement is detected before the previous switch-ON
time has elapsed. Try setting a shorter time interval.
10 Disposal
This symbol must appear on any electrical and electronic equipment placed on
the EU market. This symbol indicates that this device should not be disposed of
as unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and accumulators,
which are not enclosed by the WEEE, as well as lamps that can be removed from
the WEEE in a non-destructive manner, must be removed by end users from the
WEEE in a non-destructive manner before it is handed over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-
back of waste. Conrad provides the following return options free of charge (more details on
our website):
in our Conrad offices
at the Conrad collection points
at the collection points of public waste management authorities or the collection points
set up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be disposed of.
4
It should be noted that different obligations about the return or recycling of WEEE may apply
in countries outside of Germany.
11 Technical data
Operating voltage .......................... 220 – 240 V/AC, 50/60 Hz
Rated load ...................................... max. 1200 W resistive (e.g. incandescent lamp)
Power consumption ....................... approx. 0.5 W
Protection class .............................. II
PIR sensor activation ..................... 3 – 2000 lux (adjustable)
PIR sensor time delay .................... 10 ± 3 s to 15 ± 2 min (adjustable)
PIR sensor detection range ........... max. 8 m (<24 °C)
PIR sensor detection angle ........... 360°
PIR sensor installation height ........ 1.8 – 2.5 m
Operating temperature .................. -20 to +40 °C
Storage temperature ...................... -20 to +40 °C
Dimensions (W x H x D) ................. 90 x 111 x 58 mm
Weight (approx.) ............................ 130 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication reflects the technical status at the time of printing.
Copyright by Conrad Electronic SE.
*2918268_V1_1123_jh_mh_en 1055364875-2 I1/O1 en
max. 600 W inductive (e.g. energy-saving lamp or
LED)

Werbung

loading