Werbung
Verfügbare Sprachen
Verfügbare Sprachen
EN
SAFETY INSTRUCTIONS
IMPORTANT:
•
Do not stand on the workbench.
•
Do not exceed the maximum load for the workbench
(100 kg). Heavy objects must be placed carefully on the
workbench. Avoid heavy impacts when placing objects on
the workbench.
•
Do not use force when opening/closing the drawer.
SYMBOLS
Read the instructions.
TECHNICAL DATA
Max load
Dimensions
DESCRIPTION
Robust workbench with integrated tool pegboard. With a storage
drawer and wooden shelves. The pegboard hole size is 5 mm.
The pegboard hole spacing is 25 mm.
PARTS
1L
Left rear leg, 1x
1R
Right rear leg, 1x
2L
Left connector, 1x
2R
Right connector, 1x
3F
Top rear beam, 1x
3B
Top rear beam, 1x
4F₁
Beam, 1x
4F₂
Beam, 1x
4B₁
Beam, 1x
4B₂
Beam, 1x
5L
Left rear beam, 1x
5R
Right rear beam, 1x
6
Side beams, 4x
7
Drawer guide rails, 2x
8
Front legs, 2x
9F
Front panel for drawer, 1x
9B
Rear panel for drawer, 1x
10L
Left side panel for drawer, 1x
10R
Right side panel for drawer, 1x
11
Pegboard, 1x
12
Top shelf, 1x
13
Worktop, 1x
14
Drawer base, 1x
15
Bottom shelf, 1x
16
PVC feet, 4x
17
Drawer handles, 2x
A
Bolts M6x16mm, 12x
10
100 kg
L90.5 x W48 x H140 cm
B
Washers M6, 24x
C
Nuts M6, 12x
D
Bolts M4x10mm, 8x
E
Washers M4, 8x
F
Nuts M4, 8x
G
Joining plate, 1x
FIG.
1
ASSEMBLY
1.
Attach the left rear leg (1L) to the left connector (2L).
Attach the right rear leg (1R) to the right connector (2R).
FIG.
2
2.
Place both the rear legs on the floor with the side with
6 holes facing down. Attach the beams to both the rear
legs, starting at the top with the top rear beam (3B), and
then one beam (4B₁) in the middle and finally one beam
(4B₂) further down. The last hole is used for mounting the
pegboard in Step 10.
FIG.
3
3.
Attach 2 side beams (6) to the rear legs at the same height
as the middle beam (4B₁), and attach 2 side beams (6) at
the same height as the lower beam (4B₂). Attach both the
guide rails (7) for the drawer by the middle beam (4B₁), just
below the two side beams.
FIG.
4
4.
Screw the top end of the left front leg (8) onto the left side
beam (6), the guide rail (7) for the drawer and the middle
beam (4F₁). Screw the bottom end of the left front leg (8)
onto the left side beam (6) and the lower beam (4F₂).
5.
Repeat these steps for the right front leg (8) on the right-
hand side. Attach the PVC feet (16) to all 4 legs.
FIG.
5
6.
Fit the front (10L), sides (9B and 9F) and back (10R) of the
drawer together.
FIG.
6
7.
Stand the assembled workbench upright on its feet.
8.
Mount the drawer runners onto the guide rails (7) below the
right side beam. The runners are placed on the sides of the
drawer and then fitted to the rails in the workbench.
9.
Repeat on the left-hand side.
FIG.
7
10. Secure the pegboard (11) into place with bolts (A) through
the holes in the top rear beam (3B). Attach the two side
beams (5L and 5R) to the rear legs. Attach the top front
beam (3F) to the side beams.
11. Use the joining plate (G) to secure the pegboard to the top
edge of the workbench with bolts (A), washers (B) and nuts
(C).
FIG.
8
12. Mount the top shelf (12) with bolts (A), washers (B) and nuts
(C). Mount the worktop (13), the base of the drawer (14) and
the bottom shelf (15).
13. Fit the handles (17) to the front of the drawer (9F) with bolts
(D), washers (E) and nuts (F).
FIG.
9
Werbung
