Skil 7450 Originalbetriebsanleitung Seite 6

NOTES:
- the pressure control feature is specifi cally designed
for fast sanding at maximum sanding speed (speed
control setting 7), for it is the need for fast sanding
that provokes applying too much pressure
! be aware that the working of the pressure control
feature is not guaranteed when sanding at lower
speed control settings (1-6)
• On/off
- before switching on the tool, you should place it with
the entire sanding surface on the workpiece
- when switching on, do not apply too much pressure
on the tool
- switch on/off the tool by pulling/releasing trigger F
! be aware of the sudden impact when the tool is
switched on
! before switching off the tool, you should lift it
from the workpiece
• Switch lock 6
- pull trigger F
- press knob G with your thumb
- release the trigger
- unlock the switch by pulling again trigger F and then
releasing it
• Speed control 7 (7460)
For optimal sanding results on different materials
- with wheel H 2 you can adjust the sanding speed
steplessly from minimum to maximum
- always adjust speed to grit size used
- before starting a job, fi nd the optimal speed by
testing out on spare material
• Holding and guiding the tool 8
! while working, always hold the tool at the grey-
coloured grip area(s)
- guide the tool parallel to the working surface and
move it in circles or in a cross pattern
! do not apply too much pressure on the tool; let
the sanding surface do the work for you
- do not tilt the tool in order to avoid deep unwanted
sanding marks
- keep the ventilation slots uncovered
• Sanding
- the amount of material removed is determined by the
speed of the sanding disc
- the speed of the sanding disc diminishes relative to
the pressure applied to the tool
APPLICATION ADVICE
• For determining the optimal grit (and speed), table 9
can be used as reference
! always test out first on a piece of scrap material
• For more tips see www.skileurope.com
• Vibration level
The vibration emission level stated at the back of this
instruction manual has been measured in accordance
with a standardised test given in EN 60745; it may be
used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with
different or poorly maintainted accessories, may
signifi cantly increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may
signifi cantly reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
MAINTENANCE / SERVICE
• Always keep tool and cord clean (especially the
ventilation slots)
- remove adhering sanding dust with a brush
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skileurope.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 0 will remind you of this when the need for
disposing occurs
F
Ponceuse excentrique 7440/7450/7460
INTRODUCTION
• Cet outil est conçu pour le ponçage à sec du bois,
plastique, métal et mastic et des surfaces peintes
• Lisez et conservez ce manuel d'instructions 3
SPECIFICATIONS TECHNIQUES 1
ELEMENTS DE L'OUTIL 2
A Support plateau
B Vis du support plateau
C Disque de ponçage
D Réservoir à poussière
E Contrôle de pression (7450/7460)
8