Inhaltsverzeichnis
Werbung
EQ & FILTER EINSTELLEN
GAIN
DELAY
LOW PASS
HIGH PASS
SELECT
IN 1
ENTER
SELECT
ENTER
PEQ 1
PEQ 2
IN 2
not used
PEQ 10
COMPRESSOR
do not change
LIMTER
do not change
LINK
18
SET EQ & FILTERS
SELECT
adjust volume in
-9,00db
+/-0.25 dB steps
ENTER
SELECT
adjust delay in
0,020ms
0.020 ms steps
ENTER
SELECT
adjust frequency in
Freq.
10 hz steps
SELECT
selects filter type
Type
(Bessel, Butterworth,
Linkwitz-Riley)
ENTER
SELECT
switches Low Pass
Enabled
ON or OFF
SELECT
adjust frequency in
Freq.
1 hz steps
SELECT
selects filter type
Type
(Bessel, Butterworth,
Linkwitz-Riley)
ENTER
SELECT
switches High Pass
Enabled
ON or OFF
SELECT
adjusts center freq.
Freq.
in 1 hz steps
SELECT
adjusts amplitude
Gain
in 0.25 dB steps
SELECT
adjust widths of filter
Q Factor
in 0.1 steps
ENTER
SELECT
selects filter type (Bell,
Type
Notch, High/Low Shelf,
All/Band/High/Low Pass)
SELECT
switches parametric
Enabled
equalizer ON or OFF
SELECT
selects threshold level
Threshold
between -48 and +24 dBu
SELECT
selects attack time
Attack
between 1 and 10.000ms
SELECT
selects hold time
Hold
between 1 and 10.000ms
SELECT
ENTER
selects release time
Release
between 1 and 10.000ms
SELECT
selects compression ratios
Ratio
between 1.2:1 and 25:1
SELECT
selects gain values
Gain
between -12 and +12dB
SELECT
selects threshold levels
Threshold
between -48 and +24dBu
SELECT
ENTER
selects release time
Release
between 10 and 100dB/s
SELECT
Fixed programming
Off
to OFF
ENTER
EQ & FILTER EINSTELLEN
Factory default:
❾
ESC
ESC
❿
170 Hz
ESC
24dB Linkw. Riley
⓫
ESC
enabled
ESC
ALLEGEMEINE HINWEISE
20 Hz
• Durch Rotieren (SELECT) und Drücken (ENTER) des EQ-
ESC
Einstellknopfes ⓬ können die vorprogrammierten Parame-
24dB Linkw. Riley
ter des DSP Prozessors verändert werden.
ESC
enabled
• Der zuletzt eingestellte Wert eines Menues bleibt aktiv,
ESC
auch wenn das Menue mit der ESC-Taste ⓫ verlassen wird.
• Nach jedem Einschalten des XD-1000 Moduls ❼ werden
ESC
die zuletzt aktiven Einstellungen geladen.
ESC
SPEICHERN & LADEN
ESC
• Durch ein- bzw. mehrmaliges Betätigen der MENU-Taste
ESC
❾ können bis zu 80 unterschiedliche DSP Einstellungen
abgespeichert und jederzeit wieder hochgeladen werden.
ESC
• Auf dem 1. Speicherplatz befindet sich die nicht editierba-
re Werkseinstellung.
ESC
ESC
MENU
LOAD
ESC
ESC
MENU
MENU
+
SAVE
ESC
MENU
MENU
MENU
ESC
+
+
ESC
MENU
MENU
MENU
+
+
ESC
ESC
SET EQ & FILTERS
MENU
MENU
SELECT
CLIP
DISPLAY
SIG
ENTER
OK
ESC
GENERAL INSTRUCTIONS
LED
• The preprogrammed parameters and settings of the DSP
SPKR
processor can be changed by rotating (SELECT) and press-
INPUT
MUTE
ing (ENTER) the EQ-control knob ⓬.
XLR
XLR
• The last settings of each menue remain active, even when
OUT
the menue has been quit with the ESC-key ⓫.
LAN
• Switching-on the XD-1000 modul ❼ will load the last
active settings of the DSP.
XLR
IN
SAVE & LOAD FILTERS
ON
OFF
USB
• Up to 80 different DSP settings can be stored and up-
12V DC TRIGGER
loaded by a singular or repeated pressing of the MENU-key.
• The first preset is programmed with the factory settings
EARTH
(non-editable).
SELECT
SELECT
select preprogr.
confirm upload
filter (up to 80)
with YES
ENTER
SELECT
SELECT
enter file name
select file name/
using SELECT &
file number
ENTER button
ENTER
ACCESS
allows to lock the DSP settings with a password
MENU
+
VERSION
displays the firmware version of the DSP
SLICE
⓬
ENTER
ENTER
MENU
SELECT
confirm to save
with YES
ENTER
19
Werbung
Inhaltsverzeichnis
