Yokis 500 Serie Bedienungsanleitung Seite 8

MTR500 ELECTRONIC TOGGLE RELAY TIMING
Operation: A short press will switch the light on and off.
The MTR500 relay can also be configured with a timer to force shutdown if the user forgets to do so.
Timing: The timing is deactivated by default.
It can be configured from 2 seconds to 4 hours by means of successive rapid pressures (see Table of
configurations).
Press briefly 25 times to set the duration in seconds (from 2 seconds to 4 minutes): (reply: 5 flashes).
Press briefly 26 times to return to duration in minutes (from 2 minutes to 4 hours) (reply: 6 flashes).
Warning: The module, if timed, indicates the approaching of the shutdown by a brief blinking flashing followed
by a warning time, during which it stays on. The warning period (1 minute if timing is set in minutes, 15 seconds
if timing is set in seconds) is added to the previously set lighting time of the module. A short press of the button
during the warning period will restart timer. Press briefly 24 times to disable (or reset) the warning function
(reply: 4 flashes). The warning function is disabled by default.
Soft start and soft stop: this function allows progressive switching on and off to increase the life of
incandescent or halogen lamps. Press briefly 20 times to activate (or deactivate) this function (reply: 10
flashes). The function is deactivated by default.
Extended time 1 hour: Press one of the connected buttons for longer than 3 seconds to switch on the light for
one hour (a brief flashing of the light indicates that the control has been recognised). After the time has elapsed,
the module starts working normally again. Simply press a button to switch off the unit before the hour has
elapsed. Press briefly 29 times to disable (or re-enable) the "extended time" function (reply: 9 flashes). The
function is activated by default.
Note: When the Soft Start, Soft Stop and Warning functions are enabled, the light is dimmed gradually during
the warning time as well. When programmed in seconds, the light is dimmed by 20% every 3 seconds. When
programmed in minutes, it is decreased by 20% every 12 seconds.
MTM500 STAIRCASE LIGHTS TIMER
The MTM500 staircase lights timer is used to time the staircase lights.
Operation: Press the pushbutton on the landing shortly to switch the light on for a programmed time. Press the
pushbutton again will extend the on time.
Timing: The timing is preset to 2 minutes. To change the value, see the corresponding section of the MTR500.
Warning: See MTR500. However, in this case the function is enabled by default.
Soft start e soft stop: See MTR500. The function is disabled by default.
Extended time 1 hour: Hold one of the connected buttons pressed for longer than 3 seconds to turn the light
on for one hour (the light will blink to indicate that it was recognised). When the hour is over, the module will
start working normally again. Switching off cannot be anticipated. Press the button connected to the module
briefly to turn the light back on again for the programmed time. Hold the button pressed to turn the light on again
for one hour.
Note: When the Soft Start, Soft Stop and Warning functions are enabled, the light is dimmed gradually during
the warning time as well. When programmed in seconds, the light is dimmed by 20% every 3 seconds. When
programmed in minutes, it is decreased by 20% every 12 seconds.
MTV500 TIMED DIMMER
The MTV500 timed dimmer also manages the timing and courtesy night light functions.
Operation: A short press will switch the light on or off at 100%. Press twice to set the
lighting to the stored intensity setting.
Hold the button pressed (with the light on) to change brightness and store the setting.
The brightness level reached is stored when the button is released.
The direction of change is reversed whenever the button is pressed.
100% light: A brief press of the button increases brightness to 100% (default setting).
Memory recall: The last brightness level set by means of a long press is stored to be recalled at the next power
on by two brief presses (default setting).
Mode 100% or recall short press memory: In some applications it is preferable to recall the memory the first
time you press it. In this case, two presses are required to obtain 100% lighting. Press 29 times briefly to switch
this mode on or off. The module is configured to 100% mode by default.
DS1054-042B
P8
Installation Model
Flush-mounted MTR500E
DIN rail MTR500M
Installation Model Code
Flush-mounted MTM500E
DIN rail MTM500M
Installation Model
Flush-mounted MTV500E
DIN rail MTV500M
Preset dimmer settings
100%
Memory
Night courtesy 3 touches
Code
5454050
5454060
5454051
5454061
Code
5454052
5454062
1 touch
2 touches