Pepperl+Fuchs VBG-EN-K20-D Handbuch Seite 4

7 Bedienung im erweiterten Anzeigemodus ...................................... 27
7.1 EtherNet/IP (Hauptmenü) ................................................................................ 30
7.1.1 ARM Firmware ................................................................................................... 30
7.1.2 TCP/IP Object .................................................................................................... 30
7.1.2.1 IF Status ............................................................................................................ 31
7.1.2.2 IF Capability ....................................................................................................... 31
7.1.2.3 IF Control ........................................................................................................... 31
7.1.2.4 Path to Link Objec .............................................................................................. 31
7.1.2.5 TCP/IP Configuration ......................................................................................... 32
7.2 Ethernet Object ................................................................................................ 32
7.3 Quick Setup ...................................................................................................... 33
7.3.1 Control Menüs (optional) .................................................................................... 34
7.3.1.1 AS-i Control ........................................................................................................ 34
7.3.1.2 AS-i Control Information ..................................................................................... 34
7.3.1.3 AS-i Control Run ................................................................................................ 34
7.3.1.4 AS-i Control Flags (Steuerprogramm Merkerspeicher) ...................................... 35
7.4 Slave Adr Tool (Slaveadressierungstool) ...................................................... 35
7.5 Slave Test Tool ................................................................................................. 36
7.6 Setup (Konfigurieren des AS-i-Kreises) ........................................................ 38
7.6.1 AS-i Circuit (AS-i-Kreis) ..................................................................................... 38
7.6.2 Setup (Konfigurieren des AS-i-Kreises) ............................................................. 38
7.6.3 AS-i Slave Addr (Slaveadresse einstellen/ändern) ............................................ 39
7.6.4 Force Offline (AS-i-Master offline schalten) ....................................................... 39
7.6.5 Operation Mode (Betriebsmodus) ...................................................................... 40
7.6.6 Store Act Cfg (aktuelle erkannte Konfiguration speichern) ................................ 40
7.6.7 Permanent Param (Projektierte Parameter) ...................................................... 40
7.6.8 Permanent Config (Projektierte Konfigurationsdaten) ....................................... 41
7.6.9 AS-i Address Assistant (AS-i-Adressierungsassistent) ...................................... 41
7.6.10 LOS (Liste der Offline-Slaves) ........................................................................... 42
7.6.11 Auto Adr Enable (Automatisches Adressieren ermöglichen) ............................. 42
7.6.12 Factory Reset (Zurücksetzen des Masters auf Werkseinstellung) ..................... 42
7.7 IO + Param. Test ............................................................................................... 43
7.7.1 AS-i Circuit (AS-i-Kreis) ..................................................................................... 43
7.7.2 IO + Param. Test ............................................................................................... 43
7.7.3 Binary Inputs (Binäre Eingänge) ........................................................................ 44
7.7.4 Binary Outputs (Binäre Ausgänge) .................................................................... 44
7.7.5 Analog Inputs (Analoge Eingänge) .................................................................... 44
7.7.6 Analog Outputs (Analoge Ausgänge) ................................................................ 45
7.7.7 Parameter .......................................................................................................... 45
7.8 Diagnosis (normale AS-i-Diagnose) ............................................................... 46
7.8.1 AS-i Circuit (AS-i-Kreis) ..................................................................................... 46
7.8.2 Diagnose-Menü .................................................................................................. 46
7.8.3 Flags .................................................................................................................. 46
7.8.4 Actual Config (Aktuelle Konfiguration) ............................................................... 48
7.8.5 LPF (Liste der Peripheriefehler) ......................................................................... 49
7.8.6 AS-i-Master (Info) ............................................................................................... 49
7.9 Adv. Diagnosis (erweiterte AS-i-Diagnose) ................................................... 49
7.9.1 Error Counters (Fehlerzähler) ............................................................................ 50
7.9.2 LCS (Liste der Slaves, die einen Konfigurationsfehler ausgelöst haben) .......... 50
Zumutbare Änderungen aufgrund technischer Verbesserungen vorbehalten.
2
Pepperl+Fuchs GmbH · 68301 Mannheim · Telefon (06 21) 7 76-11 11 · Telefax (06 21) 7 76 27-11 11 · Internet http://www.pepperl-fuchs.com
AS-Interface
Inhaltsverzeichnis
Copyright Pepperl+Fuchs, Printed in Germany