Werbung
Verfügbare Sprachen
Verfügbare Sprachen
19611 Adapter
INTENDED USE:
- The adapter allows the mounting of selected screens
-
or speakers on stands with ø 35 mm extension tube
FEATURES & CAPABILITIES
- max. load capacity: 25 kg
- professional quality, excellent finish
- Orientation: rotatable 360°.
- Hole patterns for mounting the loads:
-
1. for direct mounting: 70 mm-M6 (3.a)
-
2. per loudspeaker adapter plates K&M-No. 24352 to 24359 (3.b)
-
3. per VESA adapter plates K&M-No. 19615, 19616, 19617, 19618 (3.b)
- Data: Weight 0.5 kg, insertion depth: 80 mm for ø 35 mm
Thank you for choosing this product. Please read and follow these instructions carefully
before installation and use. They inform you about all important steps regarding assembly
and handling. We recommend that you keep them for future reference.
SAFETY INSTRUCTIONS
ADAPTER 19611
- Max. load: 25 kg, subject to the maximum load capacity of the stand.
- Subject the product to a visual inspection: damaged parts must not be
-
used and must either be replaced or repaired.
- Install only suitable screens or speakers. Pay attention to:
-
connecting dimensions, size, weight.
- The screw connections between the load, the stand adapter and any
-
adapter plates must be firmly tightened; this condition must be checked
-
regularly.
- To prevent unintentional rotation of the adapter (and the load), the desired
-
position should be fixed by tightening the clamping screw a firmly but not
-
overtight. Hand force is enough.
- Protect installation from moisture, humidity, wind loads, etc.
- The safety instructions for the stand must be observed.
INSTALLATION INSTRUCTIONS
1. COMPONENTS
The bracket is already completely pre-assembled.
First of all, a visual inspection must be carried out to determine, as far as
recognizable, all parts are present
and in order:
a Clamping screw M8 x 16/33 mm,
b Adapter, consisting of:
b.1 Mounting rail (70 mm-M6)
b.2 Slip-on bushing (für ø 35 mm, 80 mm deep)
b.3 Threaded eye M8
2. MOUNTING ON THE STAND
2.1 Turn back clamping screw a until the thread no longer
2.1
protrudes into the inside of the slip-on bushing b.1.
2.2 Slide the slip-on bushing over the extension tube
2.2
of the stand as far as it will go (80 mm deep).
2.3 Align the stand adapter 5 and secure
2.3
position by tightening the clamping screw a.
3. MOUNTING THE LOAD
3.a DIRECT MOUNTING - WITHOUT ADAPTER PLATE
3.a.1 Conditions:
3.a.1
The screen or the speaker must have two threaded
3.a.1
sockets, with a:
3.a.1
- vertical distance of 70 mm
3.a.1
- the size M4, M5, M6 or 1/4"
3.a.1
Appropriate screws (not included in the scope of
3.a.1
delivery) are now screwed in until a distance of approx.
3.a.1
4 mm remains between the screw head (or washer)
3.a.1
and the bearing load.
3.a.2 Now hook the screw fitting into the mounting rail b.1.
3.a.3 The screws are tightened with a wrench, which is
3.a.3
made possible by the holes on the back of the slip-on
3.a.3
sleeve.
3.b INDIRECT MOUNTING - WITH ADAPTER PLATE
3.b.1 Load capacities:
3.b.1.1 LOUDSPEAKERS
3.b.1.1
Adapter plates: 24352, -54, -56, -57. -58, -59.
3.b.1.1
- Included screws: 2x M6 x 14 mm and washers
3.b.1.2 SCREENS
3.b.1.2
Adapter plates 19615 (
75/100), 19616 (100/200)
■
3.b.1.2
- Included screws: 4x M4 x 14 mm and washers
3.b.1.2
Adapter plates 19617 (
■
200), 19618 (
3.b.1.2
- Included screws: 4x M6 x 16 mm and washers/Iso discs;
3.b.1.2 -
4x M8 x 20 mm and washers/Iso discs
3.b.2 Each of the above adapter plates (24352ff, 19615 ff)
3.b.2
has two M6 threaded bolts. The enclosed flange nuts
3.b.2
are screwed onto these (keep a distance of 4 mm).
3.b.3 These nuts are now hooked into the mounting rail.
3.b.4 Tighten flange nuts with socket wrench SW10 (10 Nm).
3. MOUNTING
3.
THE LOAD
■
200/400)
1. COMPONENTS
2. MOUNTING ON
2.
THE STAND
3.a DIRECT MOUNTING - WITHOUT ADAPTER PLATE
3.b INDIRECT MOUNTING - WITH ADAPTER PLATE
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
19611-000-55 Rev.01 03-80-961-00 7/23
Werbung
