nedis SPBT6100BK Kurzanleitung Seite 4

a
Quick start guide
Bluetooth® Speaker Set
For more information see the extended manual online:
ned.is/spbt6100bk
Intended use
This product is a pair of stereo Bluetooth® speakers intended to
stream audio from your media device via Bluetooth® or an audio
cable.
This product is intended for indoor and outdoor use.
This product is not intended for professional use.
Any modification of the product may have consequences for safety,
warranty and proper functioning.
Main parts (image A)
Main speaker
1
Second speaker
2
RCA inputs
3
4 AUX input (main speaker
only)
Using the remote (image B)
Power button
1
Mute button
2
3 Volume up button
4 Previous track button
Start/pause button
5
Mode button
6
Power button B
1
Mute button B 2
Volume up button B
3
Previous track button B 4
Start/pause button B
5
Mode button B 6
EQ button B
7
Bass button B
8
Next track button B
9
Volume down button B
q
Battery compartment B
w
Safety instructions
-
WARNING
• Ensure you have fully read and understood the instructions in
this document before you install or use the product. Keep the
packaging and this document for future reference.
• Only use the product as described in this document.
SPBT6100BK
Power cable
5
Remote
6
3.5 mm audio cable
7
8 RCA cable
9 Speaker cable
EQ button
7
Bass button
8
9 Next track button
q Volume down button
Battery compartment
w
Switch the product on and off.
Mute the speakers.
Increase the audio volume.
Skip to the previous track.
Start and pause the current
track.
Switch between Bluetooth®
and AUX mode.
Cycle though audio profiles;
Flat, Jazz, Rock and Pop.
Increase the bass by dB.
Skip to the next track.
Decrease the audio volume.
• Do not open the product, there are no user serviceable parts
inside.
• Do not use the product if a part is damaged or defective.
Replace a damaged or defective product immediately.
• Disconnect the product from the power source and other
equipment if problems occur.
• Do not drop the product and avoid bumping.
• This product may only be serviced by a qualified technician for
maintenance to reduce the risk of electric shock.
• Do not expose the product to high pressure water or moisture.
• Do not immerse the product in water.
• Do not expose the product to direct sunlight, naked flames or
heat.
• Extended exposure to high volumes can cause hearing loss.
Connecting the speakers
Connect the speakers with the RCA cable A
A
9 .
Option A: RCA cable
1. Remove the rubber caps from the RCA inputs A
speakers.
2. Plug the red plugs of the RCA cable A
inputs A
3 on both speakers.
3. Plug the black plugs of the RCA cable A
cable inputs A
3 on both speakers.
Option B: Speaker cable
Twist the exposed wire between your fingers to clean up the ends.
Make sure no ends of the speaker cable A
1. Turn the RCA cable inputs A
clockwise to loosen the connectors.
2. Wind the exposed ends of the speaker cable A
metal part between the washers of both red RCA cable input
A 3 connectors.
3. Wind the exposed ends of the speaker cable A
metal part between the washers of both black RCA cable inputs
A
3 .
4. Turn the RCA cable inputs A
secure the speaker cable A
Placing the batteries
1. Open the battery compartment B
2. Place the batteries.
- Use only size AAA batteries (not included) for this product.
-
Observe the plus (+) and minus (–) marks on the battery and
the product to ensure correct placement.
3. Close the battery compartment B
Switching on the product
- Connect the speakers to each other before switching on the
product. See paragraph "Connecting the speakers".
1. Plug the power cable A
2. Press the power button B
Press the power button B
4
8 or speaker cable
3
8 into the red RCA cable
8 into the black RCA
9 are frayed.
3 on both speakers counter
9
9
on both speakers clockwise to
3
to the connectors.
9
w .
w .
5 into a power outlet.
1 to switch on the product.
1 to switch off the product.
on both
around the
around the