Worcraft RLM-20Li Gebrauchsanweisung Seite 89

30 % for fixed point mowing (spot
mode)
Raining now,
The rain sensor has been activated
returning
Close cover to
Request to close the cover
start
Charge to work Charging
paused manually or due to a power failure)
Automatic mowing was interrupted
Work interrupted,
(e.g. STOP button (9) was pressed,
please retry
cover (1) was opened)
Place inside the
Request to place the lawn mower
boundary and
inside the boundary wire
retry
Continue Press the OK button (8) to continue
working? the work or press the Back button (5)
Time set wrong Correct time
Charge to work Charging process was interrupted,
paused cause to be checked on site
Current work was Work process was interrupted, Check
stopped cause on site
Low battery The charge level of the battery does not
meet the minimum requirements at the start
voltage
of work:
Low battery,
70 % for automatic mowing 30 % for fi xed
charge to work
point mowing (spot mode)
Place the lawn mower in the charging
Low battery
station or to wait for the charging process
voltage, Return
to finish or lawn mower returns to the
to station
charging station independently
No loop singal
Check
No signal, please
boundary line and correct if necessary,
setup the loop
place the lawn mower inside the
first
boundary and restart it
Loop signal lost
Mower was Wait
locked! waiting...
process is completed
Wrong pin, kindly
Enter the PIN again
retry.
Place inside the
boundary and Place the lawn mower inside the
retry
boundary and restart it
Mower outside
Please reboot to
start the firmware
update
Restart lawn mower
Work interrupted,
please retry
Rain sensor
Rain sensor is activated
activated
Mower in the
Mower in the station
station
Mower is not in the station, If
Mower is not in
necessary, place the lawn mower in
the station
the station
Press
‚START' key to
Press the START button (3)
start
Duration at least
Indication of the time needed
30 mins
Searching for
Lawn mower searches for its signal
signal...
Copy file, please
Please wait for the copying process
wait
Please turn it off Switch off lawn mower
If necessary, carry out the update
Update fail
procedure again
See chapter "Reading out the work
Error
and error log"
was interrupted
correct installation of
until the currently running
Battery voltage
high
Cutting motor stall
Left motor stall
(e.g.
Please replace the
battery
Battery abnormal
Battery damaged
Battery
temperature
low (discharge)
Battery High temp
High charge
current
High charge
voltage
High temp
Mower lifted
Mower overturned
Mower trapped
Mower tilted
Motor over
temperature
Motor error
Emsensor
disconnect
the
Hall sensor failure
Hardware error
Ladung abnormal
Charging abnormal
Battery discharge
error
Inertial
measurement
unit (IMU) Error
Motor disconnect
Motor hall error
Motor overcurrent
Motor stall
Right motor stall
Rain sensor failure
Loop sensor failure
SPOT MODE / FIXED POINT MOWING
This function allows you to mow lawns that are otherwise
covered by seating furniture, playground equipment or similar.
1. Place the mower on the target area of the lawn.
2. If necessary, open the cover.
3. Unlock the display (10) with the 4-digit PIN (factory setting
"1111").
4. Press the OK button (8) to enter the main menu.
5. Select "Spot mode" with the arrow buttons (6)&(7). The
display shows "Close the cover to start".
6. Close the cover and the mower starts mowing with the fixed
point.
NOTE: The lawn mower mows in an anticlockwise spiral
direction and switches to "Automatic mowing" after a mowing
radius of 1 m or 3.5 minutes of mowing.
If the mower encounters an obstacle, the mower stops, the
display indicates that mowing has stopped and the mower
switches to standby mode.
When the lawn mower hits the boundary wire (11), it continues
mowing in the opposite spiral direction.
NOTE: If the mower is outside the boundary wire (11) or on
Battery voltage too high
See chapter "Removing blockages";
Check blades
bodies/defects;
If necessary, contact
cervice center.
Contact your local dealer or cervice
center for help
too Cancel charging process
Battery has a high temperature, and
let it cool down.
Cancel charging process, check
input current
Cancel charging process, check
input voltage
Cancel charging process
Lawn mower was lifted
Set lawn mower upright and restart
Clear the lawn mower and restart
Set lawn mower upright and restart
Switch off the lawn mower and let it
cool down
Contact your dealer or cervice center
for help
for foreign
the local