Nordica GIULIETTA X 4.0 Benutzerhandbuch Seite 30

NORMAL OPERATION
After having positioned the registers correctly, insert the indicated hourly wood load avoiding overloads that cause anomalous stresses and
deformations (according to the instructions on paragraph TECHNICAL DESCRIPTION). YOU sHOULD ALWAYs UsE THE PRODUCT WITH THE
DOOR CLOsED IN ORDER TO AVOID DAMAgEs DUE TO OVERHEATINg (FORgE EFFECT). THE INOBsERVANCE OF THIs RULE MAkEs THE
WARRANTY EXPIRE.
For safety reasons the door of the appliances with constructive system 1, must be opened only for the loading of the fuel or for removing the
ashes, while during the operation and the rest, the door of the hearth must remain closed.
The appliances with constructive system 2 must be connected to their own flue. The operating with open door is allowed under supervision.
IMPORTANT: FOR sAFETY REAsONs THE DOOR OF THE HEARTH CAN BE OPENED ONLY FOR THE LOADINg OF THE FUEL.
THE HEARTH DOOR MUsT ALWAYs REMAIN CLOsED DURINg OPERATION OR REsT.
With the controls positioned on the front of the appliance it is possible to adjust the heat emission of the hearth. They have to be opened
according to the calorific need. The best combustion (with minimum emissions) is reached when, by loading the wood, most part of the air for
combustion flows through the secondary air register.
NEVER OVERLOAD THE APPLIANCE. TOO MUCH FUEL AND TOO MUCH AIR FOR THE COMBUSTION MAY CAUSE OVERHEATING AND
THEN DAMAGE THE STOVE. YOU SHOULD ALWAYS USE THE APPLIANCE WITH THE DOOR CLOSED IN ORDER TO AVOID DAMAGES DUE TO
OVERHEATING (FORGE EFFECT). THE INOBsERVANCE OF THIs RULE MAkEs THE WARRANTY EXPIRE.
The adjustment of the registers necessary to reach the rated calorific yield with a depression at the stack of 10 Pa 11 Pa 12 Pa (1,0 mm 1,1
mm 1,2mm of column of water) is the following one: see chapter TECHNICAL DESCRIPTION. THE APPLIANCE WORks As AN INTERMITTENT
OPERATINg APPLIANCE.
BESIDES THE ADJUSTMENT OF THE AIR FOR THE COMBUSTION, THE INTENSITY OF THE COMBUSTION AND CONSEQUENTLY THE THERMAL
PERFORMANCE OF THE DEVICE IS INFLUENCED BY THE STACK. A GOOD DRAUGHT OF THE STACK REQUIRES A STRICTER ADJUSTMENT OF AIR
FOR COMBUSTION, WHILE A POOR DRAUGHT REQUIRES A MORE PRECISE ADJUSTMENT OF AIR FOR COMBUSTION.
To verify the good combustion, check whether the smoke coming out from the stack is transparent.
If it is white, it means that the device is not properly adjusted or the wood is too wet; if instead the smoke is gray or black, it signals that the
combustion is not complete (it is necessary a greater quantity of secondary air).
WARNINg: WHEN FUEL IS ADDED ONTO THE EMBERS IN THE ABSENCE OF A FLAME, A CONSIDERABLE AMOUNT OF FUMES
MAY DEVELOP. sHOULD THIs HAPPEN, AN EXPLOsIVE MIXTURE OF gAs AND AIR MAY FORM, AND IN EXTREME CAsEs AN
EXPLOsION MAY OCCUR. FOR sAFETY REAsONs IT Is ADVIsABLE TO PERFORM A NEW LIgHTINg PROCEDURE WITH THE
UsE OF sMALL sTRIPs.
UsE OF THE OVEN (IF PRESENT)
Thanks to the air flow for the combustion, the temperature of the oven may become remarkably affected. A sufficient flue of the chimney and
of the channels, well cleaned for the flow of burning smokes around the oven are fundamental for a good cooking result. Thick cakes and big
roasts must be introduced in the lowest level. Flat cakes and biscuits must reach the medium level. The upper level may be used to heat or grill.
The oven pan and the chrome plated oven grille may be located on different plans (see chapter Technical Description - ACCESSORIES).
WHEN COOkINg FOOD WITH HIgH HUMIDITY, CAKES WITH FRUIT OR FRUIT ITSELF, WATER OF CONDENSATION WILL BE PRODUCED.
DURING THE COOKING PROCESS SOME WATER VAPOUR IN THE FORM OF DROPS OF CONDENSED WATER CAN DEPOSIT ONTO THE TOP AND
THE SIDE OF THE DOOR. IT IS A PHYSICAL PHENOMENON.
By opening the door briefly and carefully (1 or 2 times, or even often in case of longer cooking times) you can let out the steam from the
cooking compartment and reduce condensation significantly.
OPERATION IN TRANsITION PERIODs
DURING TRANSITION PERIODS WHEN THE EXTERNAL TEMPERATURES ARE HIGHER, IF THERE IS A SUDDEN INCREASE OF TEMPERATURE IT CAN
HAPPEN THAT THE COMBUSTION GASES INSIDE THE FLUE CANNOT BE COMPLETELY SUCKED UP. THE EXHAUST GASES DO NOT COME OUT
COMPLETELY (INTENSE SMELL OF GAS).
In this case, shake the grating more frequently and increase the air for the combustion. Then, load a reduced quantity of fuel in order to permit
a rapid burning (growing up of the flames) and the stabilization of the draught.
THEN, CHECK THAT ALL OPENINGS FOR THE CLEANING AND THE CONNECTIONS TO THE STACK ARE AIR-TIGH.
IN CAsE OF DOUBT, DO NOT OPERATE THE PRODUCT.
30 ENgLIsH