Using Your Cleaner; Accessories - Hoover TELIOS EXTRA LITE TXL10HM011 Bedienungsanleitung

GETTING TO KNOW YOUR CLEANER
A. Hose
B. Bag Door
C. Exhaust Filter Cover
D. Main Cleaner
E. Carry Handle
F. Bag Door Release Latch
G. Mechanical Bag Check Indicator
H. On/off Pedal
I. Cord Reel Pedal
J. Variable Power Control slider
K. suction Regulator
L. Hose Handle
M. Accessory Holder
N. Telescopic Tube
O. Telescopic Tube Adjuster
P. suction Control slider
Q. Carpet and Floor Nozzle
R. Pre-Motor Filter Frame
s. Pre-Motor Filter
T. Exhaust Filter
U. Bag Holder
V. Bag
W. Accessory set
W1. Crevice Tool
W2. Furniture Nozzle
W3. Dusting Brush
X. Pet Hair Remover Mini Turbo Nozzle*
Y. Allergen Remover Mini Turbo Nozzle*
Parquet Nozzle*
Z.
AssEMBLING YOUR CLEANER
Remove all components from the packaging.
1. Connect the hose to the cleaner main body, ensuring it clips and locks into position.
To release the hose: simply press the two latches on the hose end and pull. [1]
2. Connect the hose handle to the upper tube end. [2]
Connect the tube lower end to the carpet and floor nozzle**. [3]
3.
Put the accessory holder on the extension tube, then fix furniture tool, crevice tool,
4.
dust brush on the holder.
* Certain Models Only ** May vary according to model

UsING YOUR CLEANER

1. Extract power cord and plug it into the power supply. Do not pull the cord beyond
the red marker. [6]
2. Adjust the telescopic tube to the desired height and raise or lower the tube to the most
comfortable cleaning position. [4]
3. After connecting the telescopic tube to the Carpet and Floor Nozzle, adjust the
suction control slider on the nozzle according to your cleaning needs [5]:
Hard Floor Cleaning: Adjust the suction control slider on the nozzle to the symbol.
Standard Carpet: Adjust the suction control slider on the nozzle to the symbol.
Long Pile Carpet: Adjust the suction control slider on the nozzle to the symbol.
To obtain the best performance and efficiency on Carpet adjust the suction
control slider on the nozzle to the symbol. [ ]
The suction control can also be used to reduce the operating push force.
4. switch the cleaner on by pressing the On/Off Pedal on the cleaner main body. [7]
5. Adjust the power level by moving the variable power control slider. [8]
6. Adjust the suction regulator to the desired level. [9]
7. switch off at the end of use by pressing the On/Off Pedal. Unplug and extract power
cord again to wind the power cord back into the cleaner.
8. Parking and storage - The tube can be parked for temporary storage while in use,
or in the storage position when not in use. [10]

ACCEssORIEs

The Crevice tool, Furniture nozzle and Dusting brush are stored on the accessory
holder.
All accessories can be fitted to the end of the handle or the end of the telescopic tube.
Crevice Tool – For corners and hard to reach areas. [W1]
Furniture Nozzle – For soft furniture and fabrics. [W2]
Dusting Brush – For bookshelves, frames, keyboards and other delicate areas. To
extend the brushes push the button on the body of the tool. [W3]
Parquet Nozzle* – For parquet floors and other delicate floors. [Z]
IMPORTANT: Do not use mini turbo nozzles on rugs with long fringes, animal hides and
carpet pile deeper than 15mm. Do not keep the nozzle stationary while brush is rotating.
2
GB
[5]
[5]
[5]