Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Dubbing at high speed
This unit is quipped with a high speed dubbing system which can save the time for dubbing by 2/3 when
compare to normal speed.
Press the " Dubbing " button (23) to " Hi " position and then follow the same procedures as stipulated
in "Dubbing at normal speed".
When dubbing a pre-recorded cassette tape at high speed, a chattering sound is being heard. To avoid
this, set the volume control to a minimum level.
Do no active/de-active the "Hi-nor. dubbing" button during dubbing, this will vary the speed of
recording and may be damage the cassette tape.
B. Recording from radio
Select " Tuner " function (6).
Tune to the desire station and insert a blank cassette tape in deck 1.
Press "Record" & "Play" key to start recording.
Press "Pause" keys and then "Stop/eject" key when finish.
C. Recording from phono
Select "Phono" function (6).
Insert a blank cassette tape in deck 1 which suitable for recording.
Press "Pause" key first and then "Record" & "Play" key at cassette. Recording function is now stand by.
Start the playback at phono and then press "Pause key" at cassette to start recording.
To stop recording, press " Pause " key and then "Stop/eject" key on cassette tape deck first, then return
the tone arm back to the rest station at phono.
Encoding of CD/phono or cassette tape into MP3 file
The system is able to encode CD, record (from phono) and cassette deck file (from tape) to MP3 format and
recording at memory media with USB connecting port or SD/MMC card.
A) CD encoding
I) recording 1 track
1.
Play the CD track you want to encode/record, as normal.
2.
Press the " Record " button (3) during playback of the desired track
3.
"
" & "
4.
After the encoding process has finished, the unit will stop playback automatically.
II) Recording the complete CD
1.
Place a CD with the printed side facing up inside the CD tray & then close the cd door.
2.
After disc search has been completed, press the " Record " button (3) – note:
do not press "Play" and then "Record", or only the selected track will be recorded.
3.
"
" & "
4.
After the encoding process has finished, the unit will stop playback automatically
III) encoding by program
1.
Place a CD with the printed side facing up inside the tray & then close the co door
2.
Select the desire tracks by following " CD disc programming " procedures. Then press "CD
Play/pause/stop " button (16) to start playback.
3.
Duying CD playback, press and hold the " CD Play/pause/stop " button (16) for 2 seconds to enter the
stop mode.
4.
Press the " Record " button (3) and the unit will display "
performing now. After completing of encoding, unit will stop playback automatically.
Remark:
The recording speed is 1:1 and according to the actual plying time of the CD/ phono or tape
-
During copy mode, the system will copy the MP file only.
-
The system will create a " audio " folder for encoding file and " fcopy " for copying file.
-
The recording format is preset at – MP3 bit rate : 128 kbps, sampling rate : 44.1khz
-
No song title will be recorded during encoding mode
-
To interrupt the recording, press the " Record " button again during record mode.
-
The system will store the file to USB source first if both USB and SD slot are being occupied during
-
encoding.
Copy MP3 file from USB/SD will be successful only entire song being copied, if terminate
-
the copying process intermediately, there is no track being recorded nor stored to the USB
or SD/MMC card
" will be flashing on the LCD display to show encoding is in progress.
" will be flashing on the LCD display to show encoding is in progress.
" & "
" & flashing. Encoding is
Werbung
Inhaltsverzeichnis
