Technical Data; Angle Grinder; Noise/Vibration Information - Bosch GWS 18V-180 P Professional Originalbetriebsanleitung

22 | English
a)
(13) Cutting disc
(14) Clamping nut
(15) Grinding spindle
a)
(16) Hand guard
a)
(17) Rubber sanding pad
a)
(18) Abrasive disc
a)
(19) Cup brush
a)
(20) Round nut
(21) Two-pin spanner for clamping nut/round nut
a)
(22) Open-ended spanner
(23) Handle (insulated gripping surface)
a)
(24) Diamond cutting disc
(25) Disc brush (dia. 22.22 mm)
a)
(26) Disc brush (M 14)
a)
(27) Conical brush
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical Data

Angle Grinder

Article number
Rated voltage
A)
Rated no-load speed
B)
No-load speed
Max. grinding disc diameter/rub-
ber sanding pad diameter
Grinding spindle thread
Max. thread length of grinding
spindle
KickBack Control
Soft start
Restart protection
Run-out brake
Weight according to EPTA-Pro-
C)
cedure 01:2014
Recommended ambient temper-
ature during charging
Permitted ambient temperature
D)
during operation and during
storage
Compatible rechargeable batter-
ies
Recommended rechargeable
batteries for maximum perform-
ance
1 609 92A 8GS | (22.02.2023)
Angle Grinder
Recommended chargers
A) Rated no-load speed for the selection of appropriate application
B) Measured at 20–25 °C with rechargeable battery Pro-
a)
C) Depends on rechargeable battery (4) and protective guard ((9),
D) Limited performance at temperatures < 0 °C
Values can vary depending upon the product and are subject to ap-
plication and environmental conditions. For further information
www.bosch-professional.com/wac.
a)

Noise/Vibration Information

Noise emission values determined according to
EN IEC 62841-2-3.
Typically the A-weighted noise level of the power tool are:
86 dB(A); sound power level 94 dB(A). Uncertainty K =
3 dB.
Wear hearing protection!
GWS 18V-180 P
Vibration total values a
determined according to EN IEC 62841-2-3:
3 601 JH6 L..
Surface grinding (roughing) and cut-off grinding:
V= 18
a
–1
min 7000 h
Grinding with abrasive disc:
–1
min 6100
a
h
mm 180
Grinding thin metal sheets or other materials that tend to easily vi-
brate with a large surface area can cause the noise emission value to
increase by up to 15 dB. Suitable, heavy damping mats can reduce
M 14
the increased noise emissions. Increased noise emissions must be
taken into consideration, both for the risk assessment of the noise
mm 22
output and for selecting suitable hearing protection.
The vibration level and noise emission value given in these
●
instructions have been measured in accordance with a
● standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
●
estimation of vibration and noise emissions.
●
The stated vibration level and noise emission value repres-
kg 2,9–4,2
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
°C 0 to +35 plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
°C –20 to +50
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
GBA 18V...
not actually being used should also be taken into account.
ProCORE18V...
This may significantly reduce vibration and noise emissions
ProCORE18V...
over the total working period.
≥ 5.5 Ah
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
tools in accordance with EN IEC 62841-2-3. The actual no-load
speed must not exceed the rated no-load speed and is therefore
lower.
CORE18V 8.0Ah and depending on the battery's state of charge
as well as the tool's operating temperature
(10)) in use
(triax vector sum) and uncertainty K
h
2 2
= 4.1 m/s , K = 1.5 m/s ,
2 2
< 2.5 m/s , K = 1.5 m/s .
GWS 18V-180 P
GAL 18...
GAX 18...
GAL 36...
Bosch Power Tools