Werbung
Safety Notes
Gloves should be worn during installation to prevent crushing and cutting
injuries.
The hot and cold supplies must be of equal pressures.
Installation Instructions
• Prior to installation, inspect the product for transport damages. After it has been
installed, no transport or surface damage will be honoured.
• The pipes and the fixture must be installed, flushed and tested as per the
applicable standards.
• The plumbing codes applicable in the respective countries must be observed.
• During initial start-up and after servicing, air in the fittings can cause noise. After
switching the jet on and off about 15 times, the noise will stop.
Technical Data
Operating pressure:
Recommended operating pressure:
Test pressure:
Hot water temperature:
Thermal disinfection:
The product is exclusively designed for drinking water!
Symbol description
Do not use silicone containing acetic acid!
To adjust the hot water limiter. Using a hot water limiter in combination with a
continuous flow water heater is not recommended.
Adjustment (see page 21)
To adjust the hot water limiter. Using a hot water limiter in combination with a
continuous flow water heater is not recommended.
Maintenance (see page 23)
The check valves must be checked regularly according to EN 806-5 in accord-
ance with national or regional regulations (at least once a year).
Dimensions (see page 22)
i
Installation example (see page 28)
Flow diagram (see page 23)
Spare parts (see page 27)
XXX = Colors
000 = Chrome Plated
670 = Matt Black
800 = Stainless Steel Optic
Cleaning (see page 24)
Operation (see page 25)
• Hansgrohe recommends not to use as drinking water the first half liter of water
drawn in the morning or after a prolonged period of non-use.
• Using the full scope of functions is only possible when the hansgrohe home app
is installed.
Fault
Insufficient water
Mixer stiff
Mixer dripping
Water escaping at the threaded base
4
English
• Possible for different water types and volumes.
• It is possible to set an individual output volume up to max. 1100 ml for each of
• If the desired volume was exceeded by mistake, stop the teaching procedure by
• A suitable water volume for the desired water volume must be taught before-
• The water output can be interrupted at any time by pressing any button.
Environmental Protection
max. 1 MPa
The packaging materials can be recycled. Please do not throw the packaging into
0,1 - 0,5 MPa
household waste, but recycle it.
1,6 MPa
(1 MPa = 10 bar = 147 PSI)
max. 60°C
70°C / 4 min
Electrical and electronic devices often contain components that may pose a
potential hazard to human health and the environment if handled or disposed of
incorrectly. However, these components are necessary for the proper operation of
the device. Devices marked with this symbol must not be disposed of with
household waste.
Troubleshooting
• A red glowing LED on the mixer indicates an error status; in that case check the
• A yellow LED on the fitting indicates an ongoing cleaning; in that case check
• A white glowing LED on the mixer indicates an operating message; these
Cause
- Aerator calcified, dirty
- Cartridge defective, calcified
- Cartridge defective
- O-ring at the connection hose defective.
Assembly (see page 19)
Setting portioned water output
(see page 26)
the three water types.
waiting for approx. 10 s and then restart it.
Retrieving portioned water output
(see page 26)
hand.
Old appliances contain valuable recyclable ma-
terials that should be recycled. Batteries, oil and
similar substances must not be allowed to enter
the environment. Therefore, please dispose of
old appliances via suitable collection systems.
error code on the device and follow the instructions in the trouble shooting chart
of 76835000.
the error code on the device and follow the instructions in the troubleshooting
chart of 76835000.
concern cleaning, flushing, water output, portioned water output, etc.
Remedy
- Clean aerator, replace as necessary
- Exchange cartridge
- Exchange cartridge
- Exchange O-ring
Werbung
