Channels & Inputs - Panasonic TX-55MZ800E Bedienungsanleitung

press and hold the Home button on the remote or press
the Right directional button consecutively on the Home
Screen. If Basic TV installation is performed during
the initial setup, highlight the Dashboard item on the
Home Screen and press OK.
You can use the Right and Left directional buttons,
OK, and Back/Return buttons to navigate through
the menu tree.
Channels & Inputs
The content of this menu may change depending on
the selected input source and whether the channel
installation is completed.
Channels
Analogue
Channel Scan: Start a scan for analogue channels.
You can press OK or the Back/Return button to
cancel the scan. Then press OK or the Back/Return
button again to exit. The channels that have already
been found will be stored in the channel list.
Update Scan: Search for updates. Previously
added channels will not be deleted, but any newly
found channels will be stored in the channel list.
You can press OK or the Back/Return button to
cancel the scan. Then press OK or the Back/Return
button again to exit.
Analogue Manual Scan: Start a channel scan
manually. First, enter the start frequency for the
scan. Then select the scanning direction and press
OK or the Right directional button to start scan. The
found channels will be stored in the channel list. You
can press the Back/Return button to cancel the
scan. Then press the Back/Return button again or
highlight Finish and press OK to exit.
Antenna
Channel Scan: Start a scan for digital terrestrial
channels. You can press OK or the Back/Return
button to cancel the scan. Then press OK or the
Back/Return button again to exit. The channels
that have already been found will be stored in the
channel list.
Update Scan: Search for updates. Previously
added channels will not be deleted, but any newly
found channels will be stored in the channel list.
You can press OK or the Back/Return button to
cancel the scan. Then press OK or the Back/Return
button again to exit.
Single RF Scan: Set the RF Channel option by
using the Right/Left directional buttons. Signal
Level and Signal Quality of the selected channel
will be shown. Press OK to start scan on the
selected RF channel. The found channels will be
stored in the channel list. You can press the Back/
Return button to cancel the scan. Then press the
Back/Return button again or highlight Finish and
press OK to exit.
Manual Service Update: Start a service update
manually. You can press OK or the Back/Return
button to cancel the scan. Then press OK or the
Back/Return button again to exit.
LCN: Set your preference for LCN. LCN is the Logical
Channel Number system that organises available
broadcasts in accordance with a recognisable
channel number sequence (if available).
Channel Scan Type: Set your scan type preference.
Channel Store Type: Set your store type prefe-
rence.
Favourite Network Select: Select your favourite
network. This menu option will be active, if more
than one network is available.
Cable
Channel Scan: Start a scan for digital cable
channels. If available, operator options will be
listed. Select the desired one and press OK. Scan
Mode, Frequency and Network ID options may be
available. The options may vary depending on the
operator and the Scan Mode selections. Set the
Scan Mode as Full if you don't know how to set up
other options. Highlight Scan and press OK or the
Right directional button to start the scan. You can
press the Back/Return button to cancel the scan.
The channels that have already been found will be
stored in the channel list.
Single RF Scan: Enter the Frequency value.
Signal Level and Signal Quality of the selected
Frequency will be shown. Highlight the Scan
option and press OK or the Right directional button
to start scan. The found channels will be stored in
the channel list.
LCN: Set your preference for LCN. LCN is the Logical
Channel Number system that organises available
broadcasts in accordance with a recognisable
channel number sequence (if available).
Channel Scan Type: Set your scan type preference.
Channel Store Type: Set your store type prefe-
rence.
Favourite Network Select: Select your favourite
network. This menu option will be active, if more
than one network is available. This option may not
be available depending on the selected country
during the initial setup process.
Satellite
Channel Installation Mode: Set this option as
Preferred Satellite or General Satellite. The
channel list will also change depending on the
selected option here. In order to watch the channels
on the satellite you want, this option should be
English - 19 -