Speed Selection Of Magpro 80 4S; Switching On The Magnet; Switching Off The Magnet - Jepson MAGPRO 40 2S Betriebsanleitung

speed. Select the coring or drilling speed according
to the material and core drill or drill bit diameter.
Proper speed yields most efficient work.

10.2. SPEED SELECTION OF MAGPRO 80 4S

With the tool properly set up. The speed selectors
are at left side and right side of gear box. There are
four stages or four speeds.
Lowest speed or stage 1:
The left hand selector adjusts to the down position
and the right hand selector adjusts to the up
position. This set up yields the lowest speed. Adjust
the speed only when tool is not turned on and not
rotating. Refer to the technical data section of the
manual for the rpm of both high and low speed.
Select the coring or drilling speed according to the
material and core drill or drill bit diameter.
Proper speed yields most efficient work.
Second speed or stage 2:
The left hand selector adjusts to the down position
and the right hand selector adjusts to the down
position. This set up yields the second lowest speed.
Adjust the speed only when tool is not turned on
and not rotating. Refer to the technical data section
of the manual for the rpm of both high and low
speed. Select the coring or drilling speed according
to the material and core drill or drill bit diameter.
Proper speed yields most efficient work.
Third speed or stage 3:
The left hand selector adjusts to the up position and
the right hand selector adjusts to the up position.
This set up yields the third speed. Adjust the speed
only when tool is not turned on and not rotating.
Refer to the technical data section of the manual
for the rpm of both high and low speed. Select the
coring or drilling speed according to the material
and core drill or drill bit diameter. Proper speed
yields most efficient work.
Highest speed or stage 4:
The left hand selector adjusts to the up position
and the right hand selector adjusts to the down
position. This set up yields the fourth or highest
speed. Adjust the speed only when tool is not
turned on and not rotating. Refer to the technical
data section of the manual for the rpm of both high
and low speed. Select the coring or drilling speed
according to the material and core drill or drill bit
diameter. Proper speed yields most efficient work.
10
Attention: Switch or selecting the
speeds of the magnetic core drill
machine must be done when the tool
motor is turned off and tool at rest not
rotating. Use one hand to rotate spindle if necessary
to get the selector to set in gear properly.

10.3. SWITCHING ON THE MAGNET

When the core drill machine is properly set up and
secured. Operator may turn on the magnet. The
magnetic holding force is available if and only if the
work surface or magnetic steel surface is not too
thin. Follow the safety recommendation of Section
8 of Start-Up. Strongest clamping power of the
magnet is available after the tool motor is turned
on. The magnetic power switch will light up when
powered on. If the light is not turned on check
the switch and replace damaged switch before
continuing work.

10.4. SWITCHING OFF THE MAGNET

With the magnetic core drill machine turned off,
tool must be at stationary position or not rotating
before the magnetic switch can be turned off.
Make sure the Magnetic core drill machine is still
properly tightened and secure before turning off
the magnetic switch. Hold onto the machine handle
tightly with one hand than turn off the magnet
switch. Always take extra precaution to prevent tool
and operator from falling.
Attention: After coring or drilling run
the tool without load for at least a
minute or when tool has become
cooler. Never overload the tool during
coring or drilling. Over heating can damage the
motor. Prevent the magnet from overheating. When
coring or drilling work is complete, do not leave the
magnetic core drill machine with the magnet power
turned on. When coring or drilling work is complete
always turn off the tool and remove as soon as
possible.
With the magnetic switch turned on and recheck
holding power of magnet and tool set up before
turning on the motor of the tool. The green button
of the motor on/off switch when pushed will start
the motor. The red button of the motor on/off
switch when pushed will stop the motor. The motor
on/off switch can be used when the magnet switch
is turned on. The motor on/off switch cannot work
when the magnet switch is turned off.
EN