Bosch EasySpray 18V-100 Originalbetriebsanleitung Seite 21

Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Ensure that the spray gun and base unit are as-
u
sembled completely and with all seals. Only this will en-
sure the function and safety of the fine-spray system.
Ensure that a nozzle cap that was delivered with the
u
spray gun is fitted. Only this will ensure the function and
safety of the fine-spray system.
Connecting the air hose (see figures A1–A2)
Connecting the base unit:
– Insert a bayonet lock (18) of the air hose securely into the
holes in the base unit port (25) according to the arrow
marks.
– Turn the bayonet lock a quarter turn clockwise.
Connecting to the spray gun:
– Insert the second bayonet lock (18) of the air hose se-
curely into the holes in the spray gun port (4) according
to the arrow marks.
– Turn the bayonet lock a quarter turn clockwise.
Note: Remove the air hose (17) before pouring in spray ma-
terial (quarter turn of the bayonet lock (18) anticlockwise;
pull the bayonet lock (18) out of the port (4)).
Attaching the carrying strap (see figure B)
To be able to reach all surfaces to be sprayed and to main-
tain flexibility, you can carry the base unit by means of the
strap (26).
– Attach one strap end to each eyelet (27).
Operation
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Work preparation
Spraying on the sides of water bodies (lakes, rivers,
u
etc.) or neighbouring surfaces in the direct catchment
area is not permitted.
When purchasing paint, lacquer and spray material, pay
u
attention to their environmental compatibility.
Preparing the spray surface
The spray surface must be clean, dry and grease-free.
– Roughen smooth surfaces and then remove the sanding
dust.
When spraying, all non-covered surfaces can be contamin-
ated by the spray mist. Therefore, thoroughly prepare the
area around the surface to be sprayed:
Bosch Power Tools
– Carefully cover floors, furnishings, doors, windows as
well as door and window frames, etc. Painting substrate,
for example, is recommended for covering the floors.
– Fix the cover material in place. Cover material that is not
fixed in place securely can be detached or blown away by
the powerful air jet.
Carefully mask off plug sockets and switches. Un-
u
covered plug sockets and switches may cause a short-cir-
cuit and increase the risk of electric shock.
Preparing the spray material
When diluting, make sure that the spray material and
u
the diluting agent are compatible. When using a faulty
diluting agent, lumps can develop that can lead to clog-
ging of the spray gun.
When diluting the spray material, make sure that the
u
flash point of the mixture is above 55 °C again after di-
luting. Diluting substances such as solvent-based lac-
quers lowers the flash point.
Note the specifications of the paint manufacturer re-
u
lating to sprayability, e.g. in the technical information
sheet or data sheet. Make sure that you do not spray
any paints that are not suitable according to the man-
ufacturer's specifications.
– Stir the spray material thoroughly.
Using spray material at room temperature will yield a bet-
ter spray pattern.
– Dilute the spray material if necessary.
If the spray test does not produce a good spray pattern,
dilute in 5 % increments until an optimal spray pattern is
achieved.
Spray material
Wood preservatives, water, oils,
thin varnishes
Impregnations, anti-rust primers
Solvent-dilutable or water-dilutable
(recommended) lacquers, primers,
radiator lacquers, thick varnishes
Dilution table
Spray mater- Diluting agent [ml] for dilution
ial
5 %
[ml]
300 15
400 20
500 25
600 30
English | 21
Recommended dilu-
tion
0 %
0−5 %
At least 5 %
10 % 15 %
30 45
40 60
50 75
60 90
1 609 92A 6FW | (13.12.2021)