Inhaltszusammenfassung für Bosch Rexroth IndraControl VCP05.2
Seite 1
The Drive & Control Company Rexroth IndraControl VCP05.2 Bedienoberfläche Widerstandsschweissen Resistance welding user interface Projektierungsbeschreibung | Project Planning Manual Edition 02 R911172348...
Seite 2
Eigenschaften. Die Angaben entbinden den Verwender nicht von eigenen Beurteilungen und Prüfungen. Unsere Produkte unterliegen einem natürlichen Verschleiß- und Alterungsprozess. Alle Rechte bei Bosch Rexroth AG, auch für den Fall von Schutzrechtsanmeldungen. Jede Verfügungsbefugnis, wie Kopier- und Weitergaberecht, bei uns.
• Bestellung VCP05.2 Diese Dokumentation richtet sich an Planer, Monteure, Bediener, Servicetechniker und Anlagenbetreiber. Diese Dokumentation und insbesondere das Rexroth IndraControl VCP05.2 Projektierungshandbuch enthalten wichtige Informationen, um das Produkt sicher und sachgerecht zu montieren, zu transportieren, in Betrieb zu nehmen, zu bedienen, zu verwenden, zu warten, zu demontieren und einfache Störungen...
6/38 Bosch Rexroth AG | Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 Darstellung von Informationen Damit Sie mit dieser Dokumentation schnell und sicher mit Ihrem Produkt arbeiten können, werden einheitliche Sicherheitshinweise, Symbole, Begriffe und Abkürzungen verwendet. Zum besseren Verständnis sind diese in den folgenden Abschnitten erklärt.
Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 Bosch Rexroth AG 7 /38 Sicherheitshinweise Dieses Kapitel enthält wichtige Informationen zum sicheren Umgang mit dem beschriebenen Produkt. Die Sicherheitshinweise sehen Sie bitte unter Tab. 1: Erforderliche und ergänzende Dokumentationen Rexroth PSI6xxx Schweißsteuerung mit Mittelfrequenz-Umrichter Betriebsanleitung und Rexroth Schweißsteuerung...
8/38 Bosch Rexroth AG | Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 Zu diesem Produkt Die vorliegende Projektierungsbeschreibung nimmt Bezug auf das Handbuch Rexroth IndraControl VCP 05.2 R911310376 Dort werden grundlegende Informationen zum Gebrauch der Kleinbedienfelder VCP05.2 gegeben:...
Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 Bosch Rexroth AG 9 /38 Überblick Das Bedienfeld VCP05.2 mit der Bedienoberfläche Widerstandsschweißen dient zur Eingabe von Parametern in Schweißsteuerungen PS6000 (SST) sowie zur Anzeige von Meldungen und Informationen aus dem Betrieb der Steuerungen.
Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 Bosch Rexroth AG 15 /38 (7) Sprache und Displaykontrast auswählen mit . Quittieren mit Bestellung VCP05.2 und Zubehör Tab. 5: Bestellung VCP05.2 und Zubehör Bestellschlüssel Bestellnummer Beschreibung mit RS232, kurz R911.328.207...
16/38 Bosch Rexroth AG | Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 PST Konfiguration Zur Verwendung mit PST6xxx bitte Projekt von CD R911171779 laden: Projekt in VCP05 laden (USB-Stick ist erforderlich) 1. Projektdaten auf USB-Stick kopieren, Pfad: TSvisRT Es können alle VCP Projekte unter dem Pfad TSvisRT...
Seite 17
Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 Bosch Rexroth AG 17 /38 3. Update auswählen. 4. Copy USB Stick auswählen . 5. Copy to USB mit auswählen. 6. Mit ok bestätigen. Die Daten inklusive der Datei HMI.Config.XML werden auf dem Stick im Verzeichnis ..\Backup\TSvisRT\ gesichert.
Seite 18
18/38 Bosch Rexroth AG | Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348...
Seite 19
Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 Bosch Rexroth AG 19/38 Contents To this Documentation ................21 Validity of the documentation ............21 Required and supplementary documentation ........21 Display of information ............... 22 1.3.1 Safety instructions ............22 1.3.2...
Seite 20
20/38 Bosch Rexroth AG | Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 The data specified above serves to describe the product. If information is also provided regarding the use, it only constitutes application examples and suggestions. Catalogue specifications are no warranted properties.
Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 Bosch Rexroth AG 21/38 To this Documentation To this Documentation Validity of the documentation This documentation applies to Rexroth VCP05.2 operator terminal with the resistance welding user interface. The content belong to •...
22/38 Bosch Rexroth AG | Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 To this Documentation Display of information In order to enable you to work with your product in a fast and safe way, uniform Safety instructions, symbols, terms and abbreviations are used. For a better understanding they are explained in the following sections.
Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 Bosch Rexroth AG 23/38 Safety instructions Safety instructions The Safety instructions refer to Tab. 1: Required and supplementary documentation Rexroth PSI6xxx Weld Timer with Medium-Frequency Inverter Instructions and Rexroth Weld Timer Safety and user information.
24/38 Bosch Rexroth AG | Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 To this product To this product The present operating and programming manual makes reference to the manual Rexroth IndraControl VCP 05.2 R911310377 which provides basic information on the use of the small operator terminal VCP05.2:...
Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 Bosch Rexroth AG 25/38 To this product Overview The VCP05.2 operator terminal with the resistance welding user interface is used for entering parameters into PS6000 weld timers (WT) as well as for displaying messages and information related to the timers’...
26/38 Bosch Rexroth AG | Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 Operation Operation Basics When the VCP05.2/RS232 operator terminal is switched on, the Start menu appears: F1 - Weld sequence/monitoring F2 – Correction F3 – Electrodes F4 –...
Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 Bosch Rexroth AG 27/38 Operation Menu structure VCP05.2 Power voltage ON only for VCP05.2/ETH: Select weld timer … All menus except Service Start menu Weld sequence Quickmode Program Monitoring basic settings...
Seite 28
28/38 Bosch Rexroth AG | Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 Operation Extension (depending on timer type) Service setup Timer data Timer start inhibit / ignition VCP data 1+2 VCP timer time Language change-over / contrast...
Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 Bosch Rexroth AG 29/38 Operation Overview of menu items and their functions Menu Abbrev. Parameter Function Comment Select weld timer WT-number enter Program selection Program number enter Weld sequence Electrode number...
Seite 30
30/38 Bosch Rexroth AG | Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 Operation IP address F6-F1 Timer data Gateway Timer type and firmware version Timer name (BOS) display Start inhibit program specific and F6-F2 Timer start inhibit/ignition...
Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 Bosch Rexroth AG 31/38 Ordering VCP05.2 (7) Select Language and Display contrast using . Acknowledge using Ordering VCP05.2 Tab. 6: Ordering VCP05.2 and acessoires Order reference Order number description with RS232, designated R911.328.207...
32/38 Bosch Rexroth AG | Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 PST Configuration For application with PST6xxx please load project from CD R911171779 : Project upload to VCP05 (USB-Stick is necassary) First of all copy the files to an USB-Stick into path TSvisRT.
Seite 33
Bedienoberfläche Schweissen / Resistance welding user interface VCP05.2 | R911172348 Bosch Rexroth AG 33/38 Ethernet Communication 3. Choose Update 4. Choose Copy USB Stick 5. Choose Copy to USB with 6. Confirm with ok The data inclusive the file HMI.Config.XML will be saved on the USB-stick in the path ..\Backup\TSvisRT\ .
Seite 34
The Drive & Control Company Bosch Rexroth AG Electric Drives and Controls P.O. Box 13 57 97803 Lohr, Germany Bgm.-Dr.-Nebel-Str. 2 97816 Lohr, Germany Tel. +49 9352 18 0 +49 9352 18 8400 www.boschrexroth.com/electrics DOK-PS6000-VCP05.2-BOF-PR02-D0-P...