Using Delay-Start Function; Keep-Warm Mode; Using Several Steam Trays - Silvercrest 16463 Bedienungs- Und Sicherheitshinweise

Initial Operation
cator
check the water level on the water level indica-
tor
12
time!
ATTENTION! HAZARD OF BURNS!
Make sure that the water does not exceed the
MAX mark
out of the steamer during operation.

Using Delay-Start Function

Note: Consider that the base of the appliance /
water tank
up to the MIN mark
as well as the condensate collection basin
8
are positioned correctly.
Press the PROG button
, the time indicator
13
symbol
Press the PLUS / MINUS button
desired delay time in 10 minute steps each
time.
Note: The set delay time refers to the current
clock time. That means if you set a delay time
of 30 minutes at 13:00, the steaming process
will start at 13:30. The maximum delay time is
24 hours.
Press the PROG button
Press the PLUS / MINUS button
or reduce the steaming time in 5 minute steps.
Note: The maximum steaming time is 90 minutes.
Note: Be aware that you might have to replen-
ish water when the steaming time is longer.
Use the openings on the sides of the conden-
sate collection basin
of the appliance / water tank
the MAX mark
1 hour of steaming.
Press the PROG button
display
PROG symbol
is now activated.
If the set delay time is elapsed, a signal tone
will sound, the pilot lamp
the appliance will start the steaming process
automatically.
10 GB/IE/CY
Downloaded from www.Manualslib.com
20 again (see fig. A). Therefore, regularly
and replenish sufficient water in good
. Otherwise, hot water may spurt
19
has to be filled with water at least
10
9 . Ensure that the turbo ring
17 . In the LCD-display
as well as the PROG
20
(see fig. A) will appear.
21
16
again.
17
16
for refilling. If the base
7
is filled up to
10
19 , it will be sufficient for approx.
again. In the LCD-
17
13 the time indicator 20 as well as the
21 will appear. The delay-start
15 will glow red and
manuals search engine
ATTENTION! HAZARD OF BURNS!
The appliance will become hot during use.
Beware of getting in contact with the ascend-
ing steam or any components.
Note: If the supply of water is used up during
use, a signal tone will sound. The steaming
process gets stopped. Therefore, regularly
check the water level on the water level indica-
tor
12 and replenish sufficient water in good
time!
ATTENTION! HAZARD OF BURNS!
Make sure that the water does not exceed the
MAX mark
out of the steamer during operation.
Press the PROG button
delay start. The PROG symbol
7
display
13

Keep-Warm Mode

to set the If the steaming time is elapsed, the appliance will
automatically switch over to keep-warm mode.
- In the LCD-display
well as the keep-warm symbol
- The pilot lamp
- In keep-warm mode, the water is heated for
approx. 2 minutes, followed by a pause of
approx. 8 minutes without heating. In this way,
to increase food is kept warm in the steamer at a tempera-
ture of 60 - 70°C.
ATTENTION! HAZARD OF BURNS! The
appliance will become hot during use. Beware
of getting in contact with the ascending steam
or any components.
- The keep-warm mode will remain active until
the supply of water is used up.
Press the ON / OFF button
keep-warm mode.

Using Several Steam Trays

Place the largest food or this with the longest
steaming time (e.g. also rice) in the lower
steam tray
. Otherwise, hot water may spurt
19
17 to terminate the
in the LCD-
21
will go out.
13 the time indicator
22 will appear.
will glow green.
15
to terminate the
14
.
6
20 as