Werbung
SUMMARY:
- Preparing the ground
- Erecting the sides of the pool
- Console screwing and wall reinforcements
- Putting up the supports for the sides of the pool
- Installing the felt underlay and the liner
- Cutting out the liner to fit the backwash inlet
nozzle and the skimmer
- Assembly of the pine edging
- The ladders
3a - Positioning the brackets. If you are using wood composite coping, lower the bracket by 2 mm.
3b - Mark in the position of the brackets according to their height on the sides of the pool.
3c - Mark in the pre-drilling points on the side where the skimmer goes.
3d - Drill the holes for screwing in all the brackets.
3e - Put in the brackets and screw them in so that the screw heads are fully embedded into the wood.
3f - Fix on the wooden stops for the skimmer flaps.
3g - Cut the 45x135 cross-section post to size for the skimmer.
3h - Cut the wall reinforcement posts (cross-section 45x135) to the height of the swimming pool.
3i - Mark the position of the holes and arrange the posts. Drill through the walls on each plank.
3j - Screw all planks and countersink all screw heads.
3k - Note the placing of the brace covers.
3l - Mark in the points where the brace covers will be screwed in and drill the sides of the structure.
3m - Screw in the supports, fully embedding the screw heads.
3n - Nail the 3 sections of the brace cover together.
4a - Screw in the skimmer intake in the upper plank using the two screws provided in the skimmer box.
4b - Install the outer seal of the skimmer and the skimmer itself.
4c -Fix on the whole unit tightening it really well to ensure it is completely waterproof.
4d - Drill the tracks according to the measurements (3 cm from the ends and then approximately every 20 cm).
4e - Screw in the first track of the liner.
4f - Mark out where the corner cut is to be made.
4g - Cut the corners according to the diagram.
4h - Fit one of the skimmer seals.
4i - Fit a seal for the backwash inlet. It must make contact with the wood.
5a - Mettre en place le feutre de protection pour le sol, de dimension 2 x 7 m.
5b - Cut out the protective felt underlay using a Stanley knife or a pair of scissors.
5c - Put the liner in place.
5d - Fit the corners of the liner into the corners of the pool.
5e - Hook the liner on to the lip of the track
5f - Check the position of the liner and smooth out the biggest creases.
5g - Adjust the corners of the liner to fit the frame of the pool.
5h - Fill the pool with water to a depth of 2 cm.
5i - Smooth out any creases and resume filling with water.
6a - Stop filling when the water is just below the backwash inlet nozzle.
6b - Position the backwash inlet nozzle from the inside of the pool.
6c - Cut a hole in the liner at the level of the nozzle, leaving approx. 2mm clearance. Put the joint and the delivery nozzle in place.
6d - Tighten the nut on the backwash inlet pipe enough to make sure it is waterproof.
6e - Bind the ends of the fittings that have been fed through with Teflon tape, working in an anti-clockwise direction. Wrap round at least 20 times.
6f - Install one of the 4m pipes and secure it using a metal collar.
6g - Put the other end of the pipe into the swimming pool and resume filling with water.
6h - Mark in the position of the skimmer seal.
6i - Put in the skimmer seal and frame.
6j - Cut out the liner on the inside of the skimmer frame. Then put in place and clip in the flange cover.
6k - The water is at the correct level when it is halfway up the skimmer (after you have put in the filter).
6l - Arrange the finishing profiles at each corner of the pool. Cut these off at the height of the swimming pool, making sure to leave 2cm clearance between the
end of the finishing profile and the edging.
6m - Fix the finishing profiles using the nails provided.
7
• (see page 28)
8
8a - Put the ladder in position. To do that, expel the air from the steps if necessary.
8b - It can only be placed at certain points. See instructions for the cover.
8c - Secure the stainless steel supports using the bolts provided in the stainless steel ladder box.
NOTICE 400x610 - H120.indd 19
1a - Installing the structure on a concrete slab base is obligatory. The slab should be at
least 20 cm thick. Ensure that the base is completely flat and level. Be sure to make a reentrant
for the metal cradle.
For the warranty to be valid, a concrete slab must be in place.
1b - Swimming pool should be oriented so that skimmer inlet face prevailing wind, in order to optimise
surface particle filtration. For this, use temporarily the first row of planks. One half plank must be
directly below the skimmer.
1c - Assemble the horizontal brace to the two vertical posts.
1d - Position of the metal cradle. Fill the reentrant with concrete.
2a - Assembly principle. For this, use the sacrifice part for fitting together all the planks.
2b - Make the first row of planks level.
2c - Push on the ends of the walls to press the structure onto the cradle.
2d - Control the shape using a tape measure (10m).
2e - Position the water jet plank on the 6th row. This can be either to the right or the left of the
skimmer.
2f - Position the lower skimmer plank on the 8th full row. Ensure that the upper and lower skimmer
planks are properly aligned.
If using a safety tarpaulin, make sure to centre
the stainless steel ladder on the edging.
18
27/10/10 09:26
Werbung
