6-channel full range digital
power amplifier (24 Seiten)
Inhaltszusammenfassung für RoDEK R2100A2
Seite 1
INSTALLATION GUIDE 1 - C h a n n e l P o w e r A m p l i f i e r 2 - C h a n n e l P o w e r A m p l i f i e r 4 - C h a n n e l P o w e r A m p l i f i e r...
INHALTSVERZEICHNIS / CONTENTS Seite Seite TECHNISCHE MERKMALE ......4 TECHNICAL FEATURES ......20 1.
Seite 3
1- / 2- AND 4-CHANNEL POWER AMPLIFIER Herzlichen Glückwunsch! Wir gratulieren Ihnen zum Kauf dieser RODEK Car-Hifi Endstufe. Damit Sie die Wiedergabequalität und die Leistungsfähig- keit dieses Verstärkers voll ausschöpfen können, bitten wir Sie, sich eingehend mit den Möglichkeiten und technischen Features dieses Car-Amps vertraut zu machen.
TECHNISCHE MERKMALE ■ Car-Hifi Verstärker zur Realisierung eines einbaufreund- ■ Phase Shift Control, variabel zwischen 0-180° lichen, leistungs- und klangstarken System Konzeptes ■ Innovatives Gehäusedesign mit Clam-Shell Aluprofil ■ Zwei MOSFET Netzteile (R4100A2 / R2180A2) sorgen für Kühlkörper und innenliegendem, temperaturgesteuer- kräftige Ausgangsleistung und hohe Stabilität tem Lüfter ■...
1. EINGÄNGE - AUSGÄNGE - BEDIENUNGSELEMENTE 1. Cinch Eingangsbuchsen (CH1/CH2, CH3/CH4; jeweils 9. Regler zum Einstellen der Tiefpass-Trennfrequenz der Kanäle CH3/4 (LOWPASS) an der integrierten elektroni- immer linker und rechter Kanal). NF-Signal Eingang für den schen Frequenzweiche Anschluss der Cinch-Ausgänge des Steuergerätes 2.
Seite 6
1. EINGÄNGE - AUSGÄNGE - BEDIENUNGSELEMENTE FRONT PANEL R2100A2 R2180A2 REAR PANEL R2100A2 R2180A2 Amplifier internal ventilation A = air inlets (top) B = air outlets (bottom)
Seite 7
1. EINGÄNGE - AUSGÄNGE - BEDIENUNGSELEMENTE FRONT PANEL R4100A2 REAR PANEL R4100A2 Amplifier internal ventilation A = air inlets (top) B = air outlets (bottom)
Seite 8
1. EINGÄNGE - AUSGÄNGE - BEDIENUNGSELEMENTE FRONT PANEL R1500A R1500A2 REAR PANEL R15000A R1500A2 Amplifier internal ventilation A = air inlets (top) B = air outlets (bottom)
2. MONTAGE Bevor Sie mit der Montage beginnen, erstellen Sie am stärkers gut zugänglich ist. Die Endstufe darf nicht mit der besten eine kurze Anschluss- und Installationsskizze. Be- Kfz- Chassismasse in Berührung kommen, sie muss also in achten Sie bitte, dass die Kabelführung und der gewählte jedem Fall isoliert montiert werden.
Stromkreis zum Verstärker durch das Einsetzen der Haupt- Für den Anschluss am Verstärker benötigen Sie Inbus- sicherung. Ihr RODEK Verstärker sollte nun beim Einschal- Schlüssel der geeigneten Größe, sowie ein Messer oder ten des Steuergerätes durch aufleuchten der blauen Power- eine Abisolier-Zange.
Systemkonfiguration R1500A2 / R2100A2 / R2180A2 R2100A2 R2180A2 OPERATION MODE SELECTOR CH1/2 set to HP R1500A2 ohms R2100A2 R2180A2 R1500A2 min. 2 ohms OPERATION MODE SELECTOR CH1/2 set to BP...
Seite 12
Systemkonfiguration R1500A2 / R2100A2 / R2180A2 / R4100A2 OPERATION MODE SELECTOR R1500A2 R2100A2 CH1/2 set to BP R2180A2 R4100A2 OPERATION MODE SELECTOR CH1/2 set to HP CH3/4 set to BP ohms R1500A2 min. 2 ohms...
Seite 13
Systemkonfiguration R4100A2 R4100A2 MID/ MID/ WOOFER WOOFER OPERATION MODE SELECTOR CH1/2 set to HP CH3/4 set to HP MID/ MID/ WOOFER WOOFER...
Seite 14
Systemkonfiguration R4100A2 R4100A2 OPERATION MODE SELECTOR CH1/2 set to HP ohms CH3/4 set to BP...
Seite 15
Systemkonfiguration R4100A2 R4100A2 OPERATION MODE SELECTOR CH1/2 set to HP CH3/4 set to BP...
4.1 MINIMALE LASTIMPEDANZ ßend die Eingangsempfindlichkeitsanpassung jedes Kanal- paares in Angriff genommen werden kann, gilt es zunächst Die RODEK Verstärker sind von der Auslegung der Endtran- die groben Trennfrequenzen für die angeschlossenen Laut- sistoren-Sektion auf eine sehr hohe Ausgangsleistung im 4 sprecher vorzuwählen.
4. EINSTELLUNG DER INTEGRIERTEN FREQUENZWEICHEN 4.3.2 BANDPASS FÜR KICKBASS Nun wird zuerst die Tiefpass (Lowpass) Frequenz am be- treffenden Regler eingestellt. Sinnvollerweise sollte diese SYSTEME im Bereich zwischen 50 bis 90 Hz liegen. Justieren Sie den Für den Betrieb von Kickbässen kommen zwei Filter, die Regler nach Gehör, dass der Klang im Bassbereich satt und nacheinander geschaltet sind, zum Einsatz.
4. EINSTELLUNG DER INTEGRIERTEN FREQUENZWEICHEN 4.4 ANPASSUNG DER 4.5 PHASE SHIFT EINSTELLUNG Der Phase-Shift Regler ermöglicht die Beeinflussung der EINGANGSEMPFINDLICHKEIT Phasenlage des angeschlossenen Subwoofer Systems. Mit Die korrekte Eingangsempfindlichkeitseinstellung ist wich- diesem Regler - und gegebenenfalls durch zusätzliches tig für die Ausnutzung des optimalen Dynamikspielraumes Umpolen des Subwoofers, ist es möglich eine perfekte Ihrer Steuergerät / Verstärker / Lautsprecherkombination.
Seite 19
Congratulations! and thank you for choosing this RODEK Car Audio Power Amplifier! To maximize the performance of your complete car audio system, it is recommended that you acquaint yourself thoroughly with the capabilities and features of this amplifier. Therefore read this manual carefully, before...
TECHNICAL FEATURES ■ Car audio amplifier for a compact and user friendly ■ Uncompromising heatsink design, introducing a new realization of a powerful car audio system clamshell structure with temperature controlled internal fan ■ Two independent MOSFET power supplies (R4100A2 / ■...
1. INPUTS - OUTPUTS - CONTROLS 9. Lowpass crossover frequency control, to adjust 1. RCA inputs (CH1/2, CH3/4, left and right channels), the cut-off frequency of the channels CH3/4 Line inputs for connection with RCA line-out’s of the head-unit 10. Slide switch to activate/deactivate the phase-shift control 2.
Seite 22
1. INPUTS - OUTPUTS - CONTROLS FRONT PANEL R2100A2 R2180A2 REAR PANEL R2100A2 R2180A2 Amplifier internal ventilation A = air inlets (top) B = air outlets (bottom)
Seite 23
1. INPUTS - OUTPUTS - CONTROLS FRONT PANEL R4100A2 REAR PANEL R4100A2 Amplifier internal ventilation A = air inlets (top) B = air outlets (bottom)
Seite 24
1. INPUTS - OUTPUTS - CONTROLS FRONT PANEL R1500A R1500A2 REAR PANEL R15000A R1500A2 Amplifier internal ventilation A = air inlets (top) B = air outlets (bottom)
2. MOUNTING OF THE AMPLIFIER Before you attempt the installation of your RODEK am- ged by the drilling of the holes for the amplifier mounting plifier, it is recommended to map out the complete audio screws. The above mentioned clearance of at least 5cm to all system and the respective wiring required.
3. ELECTRICAL WIRING Especially the music signal cables (RCA interconnects) 3.3 CONNECTION OF POWER CABLES should be kept far away from any potential sources of Run the positive power cable ("+12 V") directly from electrical interference i.e. electronic vehicle manage- the positive terminal of the car battery to the amplifier.
4. CROSSOVER SETTINGS 4.1 MINIMUM IMPEDANCE LOAD 4.2.1 HIGHPASS FOR COMPONENT The output stages of the RODEK amplifiers are designed AND COAXIAL SPEAKERS to give you extraordinary output power into 4 or 2 ohms Before you start your adjustments, all tone controls (i.e.
4.3 ADJUSTMENT OF PHASE SHIFT CONTROL The phase shift function of your RODEK amplifier can be activated with the corresponding slide switch. The phase-shift control enables you to match the acoustical phase relations of subwoofer and the speaker system playing in the front doors, either a component or a kick- bass system.
6. WARRANTY GARANTIEBESTIMMUNGEN Thank you for purchasing this RODEK amplifier. It is advisable to keep the original packing material for future transporting of the product. Vielen Dank, dass Sie sich zum Kauf eines RODEK Verstärkers ent- Please read the warranty specifications below carefully.