Parkside PGHSA 20-LI B1 Bedienungsanleitung Seite 21

4 . Sharpen first the teeth on one side . Turn the
saw around and sharpen the teeth of the
other side .
5 . The chain is worn and must be replaced by
a new saw chain if only approx . 4 mm of
the cutting teeth is remaining .
6 . After the sharpening, all cutting elements
must now be equal in length and width .
7 . After every third sharpening, the sharpness
depth (depth limitation) must be checked
and the height filed with the aid of a flat
file . The depth limitation should be set back
about 0 .65 mm from the cutting tooth . After
the setting back of depth limitation, round it
off a little at the front .
˜ Starting up a new saw chain
In the case of a new chain, the tensioning force
decreases after some time . Therefore, you have
to re-tension the chain after the first 5 cuts and
no later than after 10 minutes' sawing time .
m WARNING!
Never attach a new chain to a worn
u
drive pinion or place onto a damaged or
worn chain bar . The chain could spring
back or break, potentially leading to
serious injury .
˜ Maintaining the chain
1 . Use cut-protection gloves when handling
the chain or the chain bar .
2 . Switch off the product and remove the
battery from the product .
[ 12 ]
3 . Remove the sprocket chain wheel covering
, the saw chain
[ 7 ]
.
[ 9 ]
4 . Check the chain bar
5 . Remove burrs and straighten the guide
surfaces with a flat file .
6 . Mount chain bar
sprocket chain wheel covering
tighten the chainsaw .
434668_2304_CZ_SK_HU_SI_02.indb 23 434668_2304_CZ_SK_HU_SI_02.indb 23
and the chain bar
10 ] [
for wear .
9 ] [
, chainsaw and
9 ] [ 10 ] [
and
7 ] [
˜ Turning the blade bar
m WARNING!
Use cut-resistant gloves when working
u
with the saw chain or with the blade bar .
The blade bar needs to be reversed
[ 9 ]
regularly after a working time of about 10
hours in order to ensure even wear .
1 . Switch off the product and remove the
battery pack from the product .
[ 12 ]
2 . Remove the sprocket cover
and blade bar
[ 10 ] [ 9 ]
3 . Turn the blade bar around its horizontal
axis and install the blade bar and chain
as described under "Installing the saw
chain and blade bar" . When doing so, pay
attention to the correct rotation direction of
the saw chain!
˜ Replacement parts /
Accessories
Compatible replacement parts for this device
can be purchased at www .Optimex-Shop .com .
Please have the order-no . ready for your order .
Orders can only be placed and processed
online . If you are not sure where you can
purchase compatible parts, please contact the
Lidl Service Hotline .
Position Description
9 6" blade bar
10 Saw chain
11 Blade encasing
Parkside 20V battery pack
PAP 20 B1
PAP 20 B2 2Ah
PAP 20 B3 4 Ah
PAPS 204 A1 4 Ah
PAPS 208 A1 8 Ah
Customers from HU (Hungary), CZ (Czech
Rep .) & SK (Slovakia) can obtain compatible
replacement batteries and chargers from the
LIDL online shop www .lidl .de . Customers from SI
(Slovenia) via www .optimex-shop .com .
, saw chain
[ 7 ]
.
Order-No
943466801
943466803
943466802
5 cells
10 cells
5 cells
10 cells
GB 23
11/3/2023 12:17:25 PM 11/3/2023 12:17:25 PM