HammerSmith M22606 Gebrauchsanweisung Seite 16

NOTE: When changing the position of the rotation
direction switch, make sure that the ON/OFF switch
for speed control is not pressed in.
WORKING WITH THE DRILL ATTACHMENT
Secure the device against being switched on
accidentally by moving the direction switch
(into the middle position). There is a risk of
injury if the device switches on unintentionally.
1. Turn the chuck anti-clockwise until the drill opening
is large enough to insert the tool (drill bit holder).
2. Insert the tool as far as possible into the chuck.
3. Turn the chuck clockwise to clamp the tool.
4. To remove the tool, turn the chuck anti-clockwise
and pull it out of the drill hole.
Selection of the desired operating mode
You can use the torque setting ring to adjust the
power produced by the screwdriver.
1 - Low power
19 - High power
A. Drilling:
When ready to drill, set the torque adjustment
ring to the drill setting. Insert the drill set
corresponding with the material into the chuck.
You can use for drilling into wood, metal,
plastic, cement, ceramics or any other similar or
comparable material.
B. Screwing: If you want to use for screwing, set the
torque adjustment ring to the appropriate torque
setting. Before choosing the setting, pay attention
to the material you want to screw into. Insert the bit
extension or the flexible bit holder into the chuck.
You can use it to attach different screws and parts.
Setting the direction of rotation
The direction of rotation of the device can be
changed using the rotational direction switch.
(see Figure 2)
1. Wait until the device has come to a standstill.
2. Move the direction switch to the desired position:
Clockwise direction of rotation: → for drilling and
screwing in screws.
Anti-clockwise direction of rotation: ← for
removal of screws.
3. When you move the direction switch to the
middle position, the device is secured against
being switched on unintentionally. The direction
of rotation may only be changed when the
machine is at a standstill.
WORKING WITH THE OSCILLATION ATTACHMENT
M22606_HammersmithMultitool_Manual_A5_20220126_TC_V02.indd 16 M22606_HammersmithMultitool_Manual_A5_20220126_TC_V02.indd 16
Secure the device against being switched
on accidentally by moving the direction
switch (into the middle position).
Note: The oscillating attachment is suitable for
cutting wood or plasterboard but not for cutting
stone or concrete walls.
1. Select the desired angle for the application.
2. Position the holes of the oscillating accessory
over the fixing pins of the mounting plate.
3. Make sure that the accessory lies flat on the
surface of the mounting plate.
4. Place the washer in the inner opening of the
oscillation accessory.
Note: Make sure that the flat side of the washer
that holds the oscillating accessory faces the
accessory.
5. Insert the fastening screw through the washer
into the rotary spindle of the oscillating
attachment.
6. Use the Allen key to tighten the fastening screw
by turning it clockwise. Do not overtighten
A. Sanding
The Delta sanding plate is fitted with Velcro fabric
for quick attachment of the sanding sheets.
Clean the sanding plate before attaching the
sanding sheet.
1. Attaching the sanding sheet: Press the sanding
sheet evenly onto the sanding plate. Make sure
that the punched holes in the sanding sheet
match up with the holes in the sanding plate.
2. Removing the sanding sheet: Simply pull the
sanding sheet off the sanding plate.
Note: Always wear suitable clothing and
protective equipment when working with the
device. Ensure that the device works correctly
before every use. Personal protective
equipment and a correctly functioning device
reduce the risk of injuries and accidents.
After switching on, move the device so that it
comes into contact with the workpiece. In order to
achieve optimal sanding results, only ever work
with sanding sheets that are in perfect condition.
Apply light and even pressure while working. This
protects the device and sanding sheet. Do not use
the same sanding sheet to sand different materials
(e.g. metal and then wood).
Selection of the sanding sheet
16
15.02.22 14:31 15.02.22 14:31