Accessories - Stanley Fatmax SFMEH230 Originalanweisungen

Inserting and removing SDS-Max accessories (Fig.
B, C)
This tool uses SDS-Max chisels (refer to the inset in FIG B
for a cross-section of a chisel shank). We recommend to use
professional accessories only.
Clean and grease the chisel shank.
u
WARNING! Do not apply lubricant to themachine.
Insert the chisel shank into the bit holder/tool sleeve (6).
u
Press and turn the chisel slightly until the sleeve snaps
into position.
Pull on the chisel to check if it is properly locked. The
u
hammering function requires the chisel to be able to move
axially several centimetres when locked in the tool holder.
To remove a chisel, pull back the tool holder/ sleeve (6)
u
and pull the chisel out of the tool holder.
WARNING! Always wear gloves when you change accesso-
ries. The exposed metal parts on the tool and accessory may
become extremly hot during operation.
Indexing the chisel position (Fig. E)
The chisel can be indexed and locked into 12 different
positions.
Insert the chisel as described above.
u
Pull forward and rotate the chisel position collar (4) in the
u
direction of the arrow until the chisel is in the desired
position.
Setting the electronic impact power control dial
Turn the dial (3) to the desired level. The higher the number,
the greater the impact energy. With dial settings from «1»
(low) to «6» (full power) the tool is extremely versatile and
adaptable for many different applications. The required setting
is a matter of experience, for example:
When chiselling soft, brittle materials or when minimum
u
break-out is required, set the dial to «1» or «2» (low);
When breaking harder materials, set the dial to «6» (full
u
power).
Fitting the side handle (Fig. A)
The side handle (1) can be mounted on the front of the
machine to suit both right hand and left hand users.
WARNING! Always operate the machine with the side handle
properly mounted.
Unscrew the side handle clamp knob (7).
u
Adjust the side handle (1) to the desired angle.
u
Slide and rotate the side handle to the desired position.
u
Lock the side handle in place by tightening the clamp
u
knob (7).
Use
WARNING! Always observe the safety instructions and
applicable regulations.
(Original instructions)
Be aware of the location of pipework and wiring.
u
Apply a pressure of approx. 20 - 30 kg to the tool.
u
Excessive force does not speed up chiselling but
decreases tool performance and may shorten tool life.
Always hold the tool firmly with both hands and ensure a
u
secure stance (Fig D). Always operate the tool with the
side handle properly mounted.
Proper hand position (Fig D)
WARNING! To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING! To reduce the risk of serious personal injury,
Proper hand position requires one hand on the side handle
(1), with the other hand on the main handle.
Switching on and off
To run the tool, press the switch (2) and turn it in 'ON
u
position.
To stop the tool, turn it in 'OFF' position and release the
u
switch (2).
Demolition, chiseling and channelling
Select the appropriate chisel, and clean and grease its
u
shank.
Insert the chisel and check whether it is properly locked.
u
Set the desired impact energy level.
u
Fit and adjust the side handle (1) and make sure it is firmly
u
tightened.
Hold the tool at main handle and side handle (1) and
u
switch on. The tool now runs in continuous operation.
Always switch off the tool when work is finished and
u
before unplugging.
Various types of chisels are available as an option. Only
Stanley FatMax recommended accessories should be used
with this product.
WARNING! Do not use this tool to mix or pump easily com-
bustible or explosive fluids (benzine, alcohol, etc.).
WARNING! Do not mix or stir inflammable liquids labelled
accordingly.

Accessories

The performance of your tool depends on the accessory used.
Stanley Fat Max accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your Stanley Fat Max corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
ENGLISH
7