Residual Risks; Electrical Safety; Using An Extension Cable - Stanley Fatmax SFMEH220 Originalanweisungen

ENGLISH
Do not recondition bits yourself. Chisel reconditioning
u
should be done by an authorized specialist.
Improperly reconditioned chisels could cause injury.
Wear gloves when operating tool or changing bits.
u
Accessible metal parts on the tool and bits may get
extremely hot during operation. Small bits of broken
material may damage bare hands.
Never lay the tool down until the bit has come to a
u
complete stop. Moving bits could cause injury.
Do not strike jammed bits with a hammer to dislodge
u
them. Fragments of metal or material chips could dislodge
and cause injury.
Slightly worn chisels can be resharpened by grinding.
u
Keep the power cord away from the rotating bit. Do
u
not wrap the cord around any part of your body. An
electric cord wrapped around a spinning bit may cause
personal injury and loss of control.
Safety of others
This tool is not intended for use by persons (including
u
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not
u
play with the appliance.

Residual risks

Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
u
Injuries caused when changing any parts, blades or
u
accessories.
Injuries caused by prolonged use of a tool. When using
u
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
u
Health hazards caused by breathing dust developed when
u
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration and noise
The declared vibration and noise emission values stated in
the technical data and the declaration of conformity have been
measured in accordance with a standard test method provided
by EN62841 and may be used for comparing one tool with
another. The declared vibration and noise emission value may
also be used in a preliminary assessment of exposure.
6
(Original instructions)
WARNING! The vibration and noise emission value during
actual use of the power tool can differ from the declared value
depending on the ways in which the tool is used. The vibration
and noise level may increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the
trigger time.
Labels on tool
The following pictograms are shown on the tool , along with
:
the date code:
WARNING! To reduce the risk of injury, the user
O
must read the instruction manual.
Wear safety glasses or goggles.
N
Wear ear protection.

Electrical safety

#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised Stanley Fat Max Service
Centre in order to avoid a hazard.

Using an extension cable

Always use an approved extension cable suitable for the
power input of this appliance (see technical data).
The extension cable must be suitable for outdoor use and
marked accordingly. Up to 30 m of 1.5 mm2 H05VV-F exten-
sion cable can be used without loss of product performance.
Before use, inspect the extension cable for signs of damage,
wear and ageing. Replace the extension cable if damaged or
defective. When using a cable reel, always unwind the cable
completely.
Features
This tool includes some or all of the following features.
1. Side handle
2. Switch
3. Barrel cover
4. SDS MAX Chuck
5. Lube oil-injection inlet