Werbung
Timer: The default power on time for the
heater during startup is set to 00:00.
-
To adjust the power on time, press the
+
button for at least 2 seconds, at the same time
pressing the
< + >
or
< - >
changes the time by 1 minute, holding the button down
changes the time at high-speed.
Info: The
timer symbol
displayed.
Use the
< Menu >
button to change to the next mode.
..............................................................................................................
Timer function: Turning on or off in default set-
ting of "off" during startup.
-
To turn on the timer function, press the
+
button for at least 2 seconds, the same
button. To turn off the timer function,
time pressing the
< + >
press the
< Key >
button for at least 2 seconds, at the same
time pressing the
< - >
button.
Info: When the timer function is on, the
are displayed. When the timer function is off, only
Timer on
Timer off
is displayed.
Use the
< Menu >
button to change to the next mode.
..............................................................................................................
Waking time: Default setting during startup is
00.00.
-
To set the waking time, press the
+
button for at least 2 seconds, at the same time
pressing the
< + >
or
< - >
changes the time by 1 minute, holding the button down
changes the time at high speed.
Info:
Alarm clock symbol
Use the
< Menu >
button to change to the next mode.
..............................................................................................................
Alarm clock: Turning on and off in default set-
ting of "off" during startup.
-
To turn on the alarm clock, press the
+
button for at least 2 seconds, at the same time
button. To turn off the alarm clock press
pressing the
< + >
the
< Key >
button for at least 2 seconds, at the same time
pressing the
< - >
button.
Info: When the alarm clock is on, the
are displayed. When the alarm clock is off
and
on
off
clock symbol
and
are displayed.
Use the
< Menu >
button to change to the next mode or to
return to the initial temperature mode.
button. Tapping the buttons
will flash and
Timer on Time
timer symbol
< Key >
button. Tapping on the buttons
flashes and
on Time
is displayed.
alarm clock symbol
Service information
< Key >
-
+
increasing, and the display will switch to show the time. If no
button is pressed, the alarm will automatically silence after 10
minutes
is
Turn the alarm off using the
Snooze: Repeat alarm 8 minutes after pressing
or the
< Key >
..............................................................................................................
< Key >
-
+
phases. This is repeated until the
< Key >
buttons are pressed down at the same time for 3
seconds. After that, the memory function is reset and the
and
message appears again after 8,760 hours (12 months).
..............................................................................................................
-
+
b) Contact resistance on the measuring cable.
c) Fault in the heating element.
Actions:
to a)
Check whether the assembly plug (B2) is correctly
plugged into the thermostat (no. 1).
to b)
If a) has been carried out, then plug the assembly
plug (B2) into the thermostat (no. 1) and unplug;
repeat several times (5 to 10 times).
to c)
If a) and b) have been carried out and
continues to appear on the display then there is a
< Key >
fault with the heating element. In this case, the entire
heater must be replaced. Please contact your dealer
or our customer services department.
..............................................................................................................
alarm
-
+
-
+
Alarm setting: Snooze function or turning alarm
off.
At the set time, the alarm will sound a double-
beep tone, with the ringer volume steadily
< Menu >
button.
Reminder function: Refilling the cleaning agent /
conditioner for the waterbed.
After 8,760 hours (12 months),
on the display for 5 seconds, in 20 second
< + >
Malfunction or Error:
E 001
Possible causes:
a) Interruption between thermostat and heating
element.
Malfunction or Error:
E 002
display.
Possible causes:
a) Short circuit of the temperature sensor.
b) Interruption in the heating function/heating
element.
Measures: (to a and b): The complete heating
system must be replaced. Please contact your
dealer or our customer services department.
button.
< + >
or
< - >
Cond
will show
and
< - >
and
appears in display.
E 001
or
E 003
appears in
12
Werbung
