Operating Elements; Operation And Use; Care And Cleaning - TOOLCRAFT WL 4600 Bedienungsanleitung

6 Operating elements

4
6
5
8
9
1 On/off button with
battery status display (five LEDs)
2 LED light
3 Swivel base
4 Battery slot
5 Control button

7 Operation and use

Looking into an LED light in darkness can cause temporary blindness. This can be
dangerous in high risk environments.
Removing/inserting the rechargeable battery
To remove the rechargeable battery from the work light, press and hold the unlock button
on the rechargeable battery and then remove the rechargeable battery from the work light.
Do not use any force.
To insert the rechargeable battery into the work light, simply slide the battery with correct
orientation into the corresponding battery slot on the work light until it engages. Do not use
any force.
Charging
Charge the work light for approx. 4-5 hours before first use.
Pay attention to the battery safety information!
Proceed as follows:
Remove the battery from the work light. To do this, briefly press the release button (7) on
the rechargeable battery, and then remove the battery.
To recharge the battery, connect one end of the supplied charger to the battery charging
socket (9), and the other end to a suitable 230 V power supply.
During the charging process, the LEDs (8) on the battery light up/flash and indicate the
current charging status based on the number of illuminated LEDs. The more LEDs that are
illuminated, the greater the charging level. When the battery is fully recharged, all LEDs
will be constant.
Operation
After charging, slide the battery in until it locks into place with a "click". Make sure it is
secure before letting go.
Do not use force when inserting the battery. If it does not slide in easily, the battery is not
being inserted correctly.
1
2
7
10
6 Release latch (locks the rechargeable
battery in the work light; retracts into
rechargeable battery when the unlock
button is pressed)
7 Unlock button
8 LEDs for monitoring the charge status
9 Charging socket
10 USB output (power bank 5 V/DC, 2 A
(maximum))
Press the power button (1) repeatedly to cycle between the following light modes:
Press once
Press twice
Press three times
Press four times
Press five times
The work light will turn off when the battery needs to be recharged.
The battery charging status is displayed during use via the status LEDs on the on/off button
(1). The more LEDs that are illuminated, the greater the charging level. If none of the LEDs
light up, this means that the rechargeable battery is empty and must be recharged immediately.
Low battery warning:
3
The warning starts about 10 minutes before the light switches off automatically. The warning
is indicated by switching off the light three times in quick succession. This function is repeated
every 15 seconds. When this occurs, charge the battery pack immediately.
Control button and LED indicators
Before using the control button, switch off the light. On one side of the rechargeable
battery there is a control button (5) and 5 LEDs. Press the control button to show
the battery capacity.
The more LEDs that are illuminated, the greater the charging level. If none of the
LEDs light up, this means that the rechargeable battery is empty and must be re-
charged immediately.
USB charging socket (power bank function)
The USB connection on the battery pack can supply devices with a max. current of 2 A.
To do this, connect the device you want to charge to a USB cable and then plug it into the charg-
ing socket (6). Disconnect when not in use. The USB charging socket (power bank function)
can only be used if the battery pack has been removed from the lamp.

8 Care and cleaning

Switch off the work light and allow it to cool down completely before cleaning it.
Before cleaning, remove the rechargeable battery from the work light or charger.
Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions, as
they can cause damage to the housing or cause the product to malfunction.
Wipe the product with a dry, fibre-free cloth.
Never immerse the product in water or other liquids.
Make sure that no liquids enter the housing.
Do not use hard brushes or sharp objects to clean the product.
9 Storage
Remove the rechargeable battery from the work light.
Fully charge the work light if you do not plan to use it for an extended period.
During extended storage periods, charge at least 2x a year to prevent deep discharge of
the battery pack.
Store the work light in a cool, dark location away from moisture.
Check the charge status on a regular basis and charge the rechargeable battery if nec-
essary.
10 Disposal
10.1 Product
All electrical and electronic equipment placed on the European market must be
labelled with this symbol. This symbol indicates that this device should be disposed
of separately from unsorted municipal waste at the end of its service life.
All owners of waste equipment are obliged to dispose of waste equipment separa-
tely from unsorted municipal waste. Before handing the old device to a collection
point, end users are required to separate old batteries which are not enclosed by
the old device, as well as lamps which can be removed from the old device without
any damage.
Distributors of electrical and electronic equipment are legally required to accept waste equip-
ment free of charge. Conrad offers the following free return options (further information is avail-
able on our website):
At our Conrad stores
At the collection points established by Conrad
At the collection points of public waste disposal agencies or at the collection systems set up
by manufacturers and distributors in accordance with the German Electrical and Electronic
Equipment Act.
The end user is responsible for deleting personal data on the old device before disposal.
Please note that in countries outside Germany, other obligations may apply to the return and
recycling of old devices.
25% brightness 750 lm
50% brightness 1500 lm
75% brightness 3000 lm
75% brightness 4600 lm
Light off