•
If the power cord is damaged, it should be replaced by the
manufacturer, a maintenance service or similar qualified
personnel to avoid danger.
•
Do not attempt to repair the unit. Do not disassemble
the unit by yourself, if any malfunction is detected or
after it was dropped, unplug the unit and apply to any
authorized service center from the contact address list
given in the warranty certificate and on the website
www.rondell.ru.
•
Transport the unit in the original package only.
•
Keep the unit out of reach of children and disabled per-
sons.
THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY. ITS
COMMERCIAL USAGE AND USAGE IN PRODUCTION AREAS
AND WORK SPACES IS PROHIBITED.
CAUTION! Metal parts of the toaster heat up strongly
during operation, do not touch them.
WARNING
•
Never try to take jammed toasts out of the operating
toaster with your hands or with a metal object, as contact
of the metal object with the heating element under voltage
may cause electric shock.
•
Unplug the toaster from the mains, wait until it cools down
and only after that remove the toasts carefully with a suit-
able wooden or plastic spatula.
•
To avoid burns, keep your hands and other open parts of
your body away from the metal parts of the toaster during
the unit operation.
BEFORE THE FIRST USE
After unit transportation or storage under cold (winter)
conditions, it is necessary to keep it for at least three
hours at room temperature before switching on.
– Before the first use of the toaster, remove any package
materials that can prevent normal operation of the unit.
– Make sure that the mains voltage corresponds to the volt-
age specified on the unit body.
– There is cord storage on the bottom of the unit body. You
can adjust the power cord length by folding it in the cord
storage in a corresponding way.
– Without loading toasts, plug the unit in, set the toasting
level control knob (6) to the position «7» and switch the unit
on by pressing the lever (2).
– During the first switching on the heating elements burn,
therefore occurrence of a small amount of smoke or for-
eign smell is possible. It is normal.
– If necessary, switch the toaster on for several times.
Notes: the operation mode selection buttons (3, 4, 5) are
sensory, you just need to touch the button to switch the nec-
essary operation mode on.
TIPS
– The toasting level depends on the thickness of the bread
slice, bread sort and quality. Never toast too thin or too
thick slices, the thickness of the toast should not exceed
20 mm.
– If the toasts are jammed in the slot, press the CANCEL
button (5), unplug the toaster and let it cool down. Use a
suitable wooden or plastic spatula to remove the toasts.
Do not touch the heating elements to avoid damag-
ing them.
MAKING TOASTS
– Put one or two slices of bread into the slots for bread
toasting (1).
– Insert the power plug into the mains socket.
– Set the required toasting level using the knob (6). There
are 7 toasting levels. The toasting level will be shown on
the LED display (9) as follows:
«1» – minimal toasting level;
«7» – maximal toasting level.
Note: Set the control knob (6) to the needed position.
– Press the lever (2) until it is locked, the «CANCEL» button
(5) illumination will light up.
– When the toasts are ready, the unit will be switched off
automatically, the carriage control lever (2) will return to
its initial position.
Button (5) CANCEL
If you want to stop the toasting process, press the CANCEL
button (5).
Button (4) REHEAT
You can heat up cold toasts. To do this, put the toasts into
the slots for bread toasting (1) and press the carriage control
lever (2) until it is locked. Press the REHEAT button (4), the
button (4) illumination will light up. In this mode, you can heat
up toasts without additional toasting.
Button (3) DEFROST
To toast frozen toasts, put them into the slots for bread toast-
ing (1). Set the required toasting level with the control knob
(6), press the carriage control lever (2) until it is locked and
then press the DEFROST button (3); the button (3) illumina-
tion will light up.
5
ENGLISH