Adler europe AD 1192 Bedienungsanweisung Seite 5

1. Turn the device on by pressing the STANDBY / FUNCTION button (2) once.
2. The device will turn on the radio function.
3. Press the the Vol-/Vol+ / Al.1/Al.2 Button (4,5) buttons to change the volume UP or DOWN.
Bluetooth function:
1. Turn the device on by pressing the STANDBY / FUNCTION button (2) once.
2. Press the STANDBY / FUNCTION button (2) again to change to the Bluetooth function.
3. The device will be in "Pairing" mode.
4. Find on your playback device the "AD 1192" and press PAIR.
5. After pairing the device is ready to play.
6. Control the music playback with your playback device.
Automatic frequency finding and assigning presets to each signal:
1. Turn the device on by pressing the STANDBY / FUNCTION button (2) once.
2. The device will turn on the radio function.
3. Press and hold for at least 3 seconds the CLK./MEM. Button (3).
4. The radio will start to search for radio signals and assign presets numbers to the found station.
5. Once the device has covered all of the frequencies the radio will stop searching.
Automatic radio station setup to preset stations:
1. Turn the device on by pressing the On/ Off button (2) once.
2. The device will turn on the radio function.
3. Press the PRE. Button (9).
4. You can change the preset number by pressing the Skip – and Skip + button (7,8).
5. Press the PRE. Button (9). To confirm your choice.
6. The device will switch to the frequency assigned to the preset.
Manual setting of the preset number to the radio station.
1. Turn the device on by pressing the STANDBY / FUNCTION button (2) once.
2. The device will turn on the radio function.
3. Change the frequency by pressing the SCAN – and SCAN + button (7,8).
4. Press the CLK./MEM. Button (3) once.
5. By using the SCAN – and SCAN + button (7,8) choose the desired preset number.
6. Press the CLK./MEM. Button (3) once to confirm your choice.
Choosing the preset radio station:
1. Turn the device on by pressing the STANDBY / FUNCTION button (2) once.
2. The device will turn on the radio function.
3. Press the SLEEP/PRESET Button (9).
4. PX will show. Where the X is the number of the station.
5. Press the SLEEP/PRESET Button (9) repeatedly to choose the desired preset number.
6. The radio will change to the frequency assigned to the number chosen.
AUX playback:
1. Turn the device on by pressing the On/ Off button (2) once.
2. Press the STANDBY / FUNCTION button (2) twice to change to the AUX-IN function, the display will show "AU".
3. Connect the device via the AUX port (15) on the back.
4. The device will automatically change to the AUX function.
5. Change the tracks on the playback device.
6. You can change the volume of the music by using the playback device or the Vol-/Vol+ / Al.1/Al.2 Button (4,5) buttons to change the
volume UP or DOWN.
USB Port charging:
1. Plug the device to the mains power.
2. Using an USB cable insert one side of the cable into the USB port (16) at the back of the radio.
3. Once done, unplug the USB cable.
Wireless charging:
1. Plug the device to the mains power.
2. Remove your phone from its case.
3. Put your phone that has the ability to be charged wirelessly.
4. Put the phone on the upper part of the device marked with the Lightning / Charging logo.
5. Once the phone has finished charging please remove it from the device.
Please note the thickness of your charging case. If the case is thicker than 5mm the charger will not work properly.
Due to the interference from wireless charging, the wireless charging function will be suspended under the FM radio mode.
Please use the USB charger slot to charge your device under the FM radio mode.
Cleaning and Maintenance:
1. Unplug the device from the mains power.
5