Adler europe AD 1192 Bedienungsanweisung Seite 4

device (RCD) in the power circuit, with residual current rating not more than 30 mA. Contact
professional electrician in this matter.
15. Avoid getting the device wet.
16. The device may only be wiped with a dry cloth. Do not use water or cleaning fluids.
17. The device should be kept in a dry room.
Device description (Clock radio):
1. DISPLAY
3. CLOCK / MEMORY button
5. VOLUME+ / ALARM 2 button
7. SCAN- button
9. SLEEP / PRESET button
11. WIRELESS CHARGE LOCATION
13. AC POWER CORD
15. AUX-IN JACK
Before powering the device on. Remove all packing material and read the instruction manual carefully. Keep it for future reference.
Setting up the device:
1. Remove all the packing material from the device.
2. Open the backup battery door (14).
3. Insert 2 AAA 1.5V batteries in the position shown inside.
4. Close the backup battery door (14).
5. Insert the device AC power cord (13) into the wall socket (220-240 V 50/60Hz.)
Clock setup:
1. Press and hold the Clk. / MEM. Button (3). The display (1) will start to blink.
2. Choose time format 12 / 24 H by pressing the SCAN +/- buttons (7,8).
3. Confirm your choice with the CLK / MEM (3) button by pressing it once.
Alarm 1/2 setup:
1. Press and hold the Vol-/Vol+ / Al.1/Al.2 Button (4,5). The display (1) will start to blink.
2. Choose time by pressing the SCAN – and SCAN + button (7,8).
3. Confirm your choice with the Vol-/Vol+ / Al.1/Al.2 Button (4,5). button by pressing it once.
4. Choose alarm type between BUZZ and TUNE. Buzzer or Radio. The radio choice will turn the last used radio station.
5. Confirm your choice with the Vol-/Vol+ / Al.1/Al.2 Button (4,5). button by pressing it once.
6. Choose the volume level of the Buzzer or Radio playing by pressing the SCAN +/- buttons (7,8).
7. Confirm your choice with the Vol-/Vol+ / Al.1/Al.2 Button (4,5). button by pressing it once.
Alarm turning On:
1. To turn on the alarm press the the Vol-/Vol+ / Al.1/Al.2 Button (4,5) button once.
2. The dot next to the AL-1 or AL-2 respectfully on the left side of the display (1) to signal the alarm is turned on.
3. The display (1) will also show the alarm current setting.
Snooze
Press the "SNOOZE / DIMMER" button (6) to suspend alarm sound for a few minutes.
The alarm will start again after approx. 9 minutes.
Dimmer
NOTE:
This function can be used in both "Standby Mode" and "Turned On Mode"
1. Press and hold the "SNOOZE / DIMMER" button (6) for 2 seconds to select the dimmer. Dimmer has 3 steps.
Turning on the device:
1. Press the STANDBY / FUNCTION button (2) once.
2. The device will turn on.
3. TO turn off the device press and hold the STANDBY / FUNCTION button (2) .
Radio setting:
1. Turn the device on by pressing the STANDBY / FUNCTION button (2) once.
2. The device will turn on the radio function.
3 You can change the frequency by pressing the Scan – and Scan + button (7,8).
4. You can also press and hold the Scan – and Scan + button (7,8) for the device to automatically find the next radio signal.
Volume control:
2. STANDBY / FUNCTION button
4. VOLUME- / ALARM 1 button
6. SNOOZE / DIMMER button
8. SCAN+ button
10. PLAY / PAUSE button
12. ANTENNA
14. BACKUP BATTERY DOOR
16. USB CHARGING PORT
4
.