cecotec BOLERO HEXA V 3000 BLACK Bedienungsanleitung Seite 46

ENGLISH
Warning
Slight differences in colour in the front part of the device are caused by the use of different
-
materials, like glass, plastic and metal.
The shadows on the door panels, which look like stripes, are due to reflections from the
-
interior lighting.
Enamel is made at very high temperatures. This can cause a slight colour variation. This
-
is completely normal and does not affect the device operation. The edges on thin trays
cannot be completely enamelled. As a result, these edges can be rough. This does not
affect the corrosion protection.
Always keep the device clean and immediately remove the dirt so that the appliance does
-
not accumulate lasting dirt residues.
Tips
Clean the oven interior after every use. This way, you will not cook food over this dirt.
-
Immediately remove lime, grease, starch and albumen stains (e.g. egg white).
-
Use suitable oven cookware, e.g., an oven platter.
-
Device door
You can detach the oven door to clean and disassemble the door panels.
-
The door hinges have a lock lever each. Fig. 16
-
When the lock levers are locked, the device door is locked. It cannot be detached.
-
When the lock levers are unlocked to detach the oven door, the hinges are blocked, so they
-
cannot be locked all at once.
Warning - Risk of injury
If the hinges are not blocked, they can be lock with energy. Make sure the lock levers
-
are always completely locked or, when detaching the device door, they are completely
unlocked.
The device hinges move when you open and close the door, be careful not to get caught.
-
Keep hands away from hinges.
Detaching the device door
Fig. 17
Open the door completely.
-
Open both lock levers located on the left and right.
-
Close the device door until it is completely locked.
-
With both hands, hold the door from its left and right side, and pull it upwards.
-
Attaching the device door
Fig. 18
Place the device door again following the previous steps in reverse order.
-
90
When fixing the device door, make sure both hinges match the installation holes on the
-
interior front panel.
Make sure the hinges are placed in the correct position. You must be able to introduce them
-
easily, without applying pressure. If you feel there is some resistance, check the hinges are
properly placed on the gaps.
Open the door completely. While you open the device door, you can check again if the
-
hinges are in their correct position. If they are incorrectly placed, the door will not open
completely.
Close both lock levers again.
-
Close the device door. At the same time, check once again if the door is in the correct
-
position and if the ventilation grilles are not partially blocked.
Removing the door cover
Fig. 19
The plastic cover layer on the door can discolour. To thoroughly clean it, you must remove
-
the cover.
Remove the device door as previously indicated.
1.
Press the tabs on the left and right side of the cover as shown in figure 19.
2.
Remove the door cover.
3.
After removing the door cover, the remaining door parts can be easily removed to continue
4.
with the cleaning. Once you finish cleaning the device door, place the cover back in its
position and press on it until it clicks into place.
Install the device door as described on the previous chapter.
5.
Warning
You can also remove the door cover while the door is attached to the oven.
-
After detaching the door cover, the interior door glass will be unlock, so it can easily move
-
and cause damage or injury.
Detaching the door cover and the interior glass reduces the total weight of the door. Hinges
-
are easier to move when you close the door and you can get caught in them. Keep hands
away from hinges.
Due to the previous warnings, it is advisable you do not detach the door cover unless the
-
door is detached. The warranty does not cover damage caused by improper use.
Guides
Fig. 20
To clean the guides and the interior of the oven, you can remove the guides and clean them as
shown in figure 20.
Cord substitution
Cord substitution can only be carried out by the manufacturer, Cecotec Technical Support
Service or qualified personnel.
ENGLISH
91
HEXA V 3000 BLACK