Werbung
Verfügbare Sprachen
Verfügbare Sprachen
GB
Commissioning Detectors using the D HP2000
1. Switch on D HP2000 by pressing the red power button.
2. Point D HP2000 at detector and press the DOWNLOAD button.
The D HP2000 will confirm the product's identity and call up the
correct menu of parameters and their current settings.
3. Use a combination of UP, DOWN, FORWARD and BACK buttons
to navigate the parameter menu, selecting options for each
shown. (See Tips below.)
4. When options for all parameters have been selected, point the
D HP2000 at the detector and press the UPLOAD button. The
luminaire(s) will switch off briefly during the programming pro-
cess and the D HP2000 shows DATA OK to confirm operation.
5. After a short period of inactivity (default 5 minutes), the D
HP2000 hibernates retaining the most recent settings.
Tips
i) Where there are only two options such as ON/OFF, a double
click of the OK button toggles between them.
ii) Where there are multiple options, a double click of the OK button
recalls a list of all options for that parameter. Use the UP, DOWN
and OK buttons to select.
iii) Use the OK button to go forward (through the menus) without
displaying help pages.
iv) Press UPLOAD at any time to transfer all current settings from
the handset to the product.
Note:
While commissioning can also be carried out using an D HP10
Programmer, this method does not offer access to the full range of
functions.
OneSwitch Dimming
OneSwitch dimming affords local control to the end-user whereby
a simple, momentary, push-to-make wallswitch can be used to
raise or lower the lighting level or to toggle the output ON/OFF. A
press of less than 1 second will toggle the output status while a
longer press will raise or lower the output. Each time the switch is
pressed, the direction of dimming reverses. If the switch has not
been pressed for 5 seconds, the direction will be up (brighter) –
unless the output is already above 90% (dc 8V) in which case the
direction is down.
To Test with D HC6 / D HC5 Hand-held Controller
Once the LightSpot Luminaire Controllers have been installed
within the luminaires, the D HC6 / D HC5 may be used to dim and
brighten luminaires and to switch them ON and OFF.
PEHA Lichtsteuerung – PEHA Elektro GmbH & Co. KG a Honeywell Company · Gartenstraße 49 · 58511 Lüdenscheid · Deutschland · www.peha.de · peha@peha.de
Important Additional Notes
1. A means for disconnection must be incorporated in the fixed
wiring in accordance with the current wiring regulations.
2. Although nominally 12V, the dimming output is not SELV and
therefore should be treated with the same respect as mains with
regard to wiring practice. The 0V line of the dimming output is
almost at Neutral potential.
3. The dimming control output should be connected only to the
control input of the ballasts - never to other detectors.
4. This equipment should be used to control only those ballasts
powered from the same phase as the detector.
5. Due to the fact that the photocell is on the ceiling looking down,
it is not possible for measurements made with a lux meter on
the working plane to remain constant when daylight illuminates
the ceiling and the working plane to a differing extent. Therefore,
products of this type should be regarded as capable of maintai-
ning an APPROXIMATE light level only.
6. This equipment switches lights no more frequently than would
a responsible human occupant. However, manufacturers of
some particular lighting types (e.g. '2D' luminaires) may specify
a maximum number of switching cycles in order to achieve a
predicted lamp life. Please check with the manufacturer of the
luminaires to ensure that they are compatible with automatic
controls in this respect.
7. Some devices in this product range feature a silvered surface
finish; this is intended for decorative purposes only. Care
should be taken to avoid accidental separation of the silvered
coating from the product. If the unit is built into a luminaire that
is subsequently wrapped in film having adhesive properties, it
is recommended that a layer of suitable packaging material be
used to protect the silvered area.
W4267C_DE_1204
Seite 6/7
Werbung
