Herunterladen Inhalt Inhalt Diese Seite drucken

Remote Control - Hisense HS218 Benutzerhandbuch

2.1-kanal soundbar mit drahtlos-subwoofer
Vorschau ausblenden Andere Handbücher für HS218:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 15

Remote Control

1
Switch the unit between ON and
STANDBY mode.
2
(MUTE)
Mute or resume the sound.
3 SOURCE
Select the play function.
4
(BT)
Select the Bluetooth mode.
5 VOL+/VOL-
Increase/decrease the volume level.
6
/
Skip to previous/next track in BT/USB mode.
7
/PAIR
Play/pause/resume playback in BT/USB mode.
Press and hold to activate the pairing
function in Bluetooth mode or disconnect the
existing paired Bluetooth device.
8 EQ
Select a preset sound effect.
9 SURR
Adjust the surround ON/OFF.
10 DIMMER+/-
Adjust display brightness.
11 BASS
Press "BASS" then press VOL+/- button
to increase or decrease the bass.
12 TREBLE
Press "TREBLE" then press VOL+/- button
to increase or decrease the treble.
Preparations
Prepare the Remote Control
The provided Remote Control allows the unit to
be operated from a distance.
Even if the Remote Control is operated within
the effective range 19.7 feet (6m), remote
control operation may be impossible if there
are any obstacles between the unit and the
remote control.
If the Remote Control is operated near other
products which generate infrared rays, or if
other remote control devices using infra-red
rays are used near the unit, it may operate
incorrectly. Conversely, the other products may
operate incorrectly.
Replace the Remote Control Battery
1 Press and slide the back
cover to open the battery
compartment of the
remote control.
2 Insert two AAA size
batteries (included). Make
sure the (+) and (–) ends of
the batteries match the (+)
and (–) ends indicated in
the battery compartment.
3 Close the battery
compartment cover.
6



Precautions Concerning Batteries
Be sure to insert the batteries with correct
positive "" and negative "" polarities.
Use batteries of the same type. Never use
different types of batteries together.
Either rechargeable or non-rechargeable
batteries can be used. Refer to the precautions
on their labels.
Be aware of your fingernails when removing
the battery cover and the battery.
Do not drop the remote control.
Do not allow anything to impact the remote
control.
Do not spill water or any liquid on the remote
control.
Do not place the remote control on a wet
object.
Do not place the remote control under direct
sunlight or near sources of excessive heat.
Remove the battery from the remote control
when not in use for a long period of time,
as corrosion or battery leakage may occur
and result in physical injury, and/or property
damage, and/or fire.
Do not use any batteries other than those
specified.
Do not mix new batteries with old ones.
Never recharge a battery unless it is confirmed
to be a rechargeable type.
7
Placement and Mounting
Placement
A If your TV is placed on a table, you can place the
unit on the table directly in front of the TV stand,
centered with the TV screen.
B If your TV is attached to a wall, you can mount
the unit on the wall directly below the TV screen.

Wall Mounting (if using option-B)

Note:
-
Installation must be carried out by qualified
personnel only. Incorrect assembly can result in

severe personal injury and property damage (if
you intend to install this product yourself, you
must check for installations such as electrical
wiring and plumbing that may be buried inside
the wall). It is the installer's responsibility to verify
that the wall will safely support the total load of
the unit and wall brackets.
-
Additional tools (not included) are required for
the installation.
-
Do not overtighten screws.
-
Keep this instruction manual for future reference.
1
3
A
-
Use an electronic stud finder to check the wall
type before drilling and mounting.
1. Drill 2 parallel holes (Ø 5.5-6 mm each
according to wall type) in the wall. The distance
between the holes should be 900mm.
2. Insert the supplied wall anchors into 2 screw
holes on the wall. Insert the supplied wall
bracket screws through the wall brackets into
the wall anchors. Fix and tighten the screws on
the wall.
3. Remove the screws then install the wall
mounting screws into the back of the unit.
4. Hang the unit on the wall mount brackets.
900 mm / 35.4"
2
4
8
EN
FR
DE
IT
B
ES
SL
HR
NL
CZ
SK
HU
PT
SR
MK
SQ
RO
PL
7

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis