Werbung
Verfügbare Sprachen
Verfügbare Sprachen
O P E R A T I N G I N S T R U C T I O N S
SATA Optical Drive Enclosure
Item-No. 41 08 13
Intended use
An optical drive (CD/DVD/Bluray burner) can be installed in the enclosure. The connection to a computer is
made via a USB2.0 port. A power supply unit to supply the power is integrated in the housing.
This product complies with all current National and European requirements. All names of companies and
products are the trademarks of the respective owner. All rights reserved.
Package Contents
• Enclosure with an installed power supply unit
• USB cable
• Set of screws
• Operating Instructions
• Power Cord
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe these safe-
ty instructions! We do not assume any liability for any consequential damage!
We shall not accept liability for damage to property or personal injury caused by incor-
rect handling or non-compliance with the safety instructions! The warranty will be void
in such cases.
• The unauthorised conversion and/or modification of the product is inadmissible because of
safety and approval reasons (CE).
• The built-in power adaptor's construction complies with protection class I. The power adap-
tor is only to be used with an earthed mains socket connected to the public power supply.
• Only use the product in dry indoor areas.
The product must not get damp or wet as this may damage it, danger of a fatal electric shock!
• The device is not a toy. Keep devices that operate on the mains voltage out of the reach of
children! Therefore, be especially careful when children are around. Use the product out of
the reach of children.
• Do not unplug the mains adaptor from the mains socket by pulling the cable; do not remove
the inlet connector for non-heating appliances from the drive housing by pulling the cable
either!
• Do not leave packing materials unattended. They may become dangerous playthings for chil-
dren.
• Handle the product with care, it can be damaged by impacts, blows, or accidental drops, even
from a low height.
Opening the drive enclosure, installation of a drive
Caution!
Disconnect the drive enclosure from the mains voltage first before opening it! Unplug
the mains power plug from the drive enclosure! Just switching off at the mains switch is
not sufficient!
Otherwise mortal danger by an electric shock!
• Remove the two screws from the rear plastic cover. Following that, the housing lid can easily be removed
from the bottom part.
• Insert a SATA drive (e.g. CD, DVD or Bluray burner) into the bottom part. Connect the SATA/power plug to
the corresponding connector on the drive.
If required, you can plug the 4-pole flat-pin plug for audio signals to the corresponding connector of the drive:
Red cable of the 4-pole flat-pin plug = right audio signal, on the drive labelled with „R"
White cable of the 4-pole flat-pin plug = left audio signal, on the drive labelled with „L"
Please note:
The audio signal is only available at the output of the CD/DVD drive when playing back „real"
audio CDs. When playing DVDs, MP3 CDs, data CDs and so on, no audio signal is available at
the drive's output since the decoding only takes place after the data transfer in the PC.
• Now fasten the drive to the bottom part with four M3-screws.
• Replace the housing lid, slide it from the back onto the bottom part.
• Lastly, the plastic cover that you removed before, is to be screwed tightly on the housing's rear side by using
two screws.
Connection
The connection of the drive enclosure to the mains voltage is only permitted if the enclo-
sure is assembled and bolted down as described above.
Otherwise mortal danger by electric shock!
• Switch the drive enclosure off (switch position „O"; mains switch on the rear side of the housing).
• Connect the mains socket on the drive enclosure with a mains outlet via the supplied mains cable.
• Connect the USB connection of the drive enclosure with a USB cable to a free USB port of your computer.
• Switch on the drive enclosure (switch position "I").
• Windows now recognises the drive automatically and completes the driver installation. All drivers are
already contained in Windows (at least Windows ME is required).
Handling
www.conrad.com
Version 11/09
°
Cleaning
Before cleaning the device, disconnect it from the power supply. Use a clean, dry soft cloth for cleaning.
Do not use any aggressive cleaning agents, since these may cause discolouration to the housing.
Tips & Notes
• USB2.0 devices are backwards compatible. That means that the drive enclosure with the installed CD/DVD
drive also functions on conventional, „slow" USB1.1 ports – but then only at the maximum USB1.1 speed
(effective approx. 800kByte/s to 1MByte/s).
Several MBytes/sec is possible with USB 2.0.
• The scope of delivery does not contain the recording software; it must be ordered separately; the same
applies to play-back software for DVDs.
Disposal
Technical Data
Operating Voltage: ........................................230V~/50Hz
Suitable drives: ..............................................Optical drives with SATA connection, 13.3cm (5.25")
Connection: ..................................................USB2.0/USB1.1
© Copyright 2009 by Conrad Electronic SE.
• When setting up the product, make sure that the cables are neither kinked nor pinched.
• The device must only be used in dry, closed indoor areas. The product must not get damp or
wet! Never touch the product if your hands are wet! There is a risk of a life-threatening elec-
tric shock!
• Avoid the following unfavourable environmental conditions at the installation location and dur-
ing transportation:
- Damp or excess air humidity
- Extreme cold (<0°C) or heat (>35°C), direct sunlight
- Dust or flammable gases, fumes or solvents
- Strong vibrations, impacts or blows,
- Strong magnetic fields such as those found close to machinery or loudspeakers
• Never use the product immediately after it has been taken from a cold room to a warm one.
The condensation that forms might destroy your unit. In addition, there is a risk of a fatal elec-
tric shock.
Allow the product to reach room temperature, before connecting it to the power supply and
putting it in to use. This may take several hours.
• Ensure that the insulation for the entire product is neither damaged nor destroyed.
• Check the product for damage before each use!
If you detect any damage, DO NOT connect the product to the mains supply! This presents
a danger to life!
• It can be assumed that safe operation is no longer possible if
- the device shows visible signs of damage,
- the device does not operate any longer and
- if the device was stored under adverse conditions for a long period of time or
- it has been subjected to considerable stress in transit.
• Any maintenance or repair work must only be carried out by authorised personnel.
Electrical and electronic products do not belong to the household waste!
When disposing of an unserviceable product, do so in line with the relevant statutory regula-
tions.
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
Werbung
