JBM 52980 Bedienungsanleitung Seite 3

REF. 52980
EN
INSTRUCTION MANUAL
PRODUCT PRESENTATION
This parts cleaning machine is the ideal aid for pro-
fessional cleaning of small and medium-sized parts,
components or tools.
SAFETY INSTRUCTIONS
CAUTION! Read all safety warnings and instruc-
tions. Failure to follow the warnings and instructions lis-
ted below may result in personal injury and/or serious
injury.
1. Keep the work area clean and free of obstruc-
tions.
2. Keep children away from the machine.
3. Never use the machine if you are under the in-
fluence of alcohol or drugs.
4. Read all information regarding the liquid you use
for cleaning. Do not use liquids that are flam-
mable at temperatures below 150ºC.
5. Use the pertinent protections to avoid burns
when touching hot parts.
6. If the machine is damaged, or if it has fallen
down, do not use it until it is checked by qualified
personnel.
7. Do not allow the power cord to come in contact
with hot parts of the machine or fan blades.
8. If an extension cord is necessary to connect the
machine to the power supply, make sure that the
current rating of the extension cord is equal to
that required by the machine. If an extension cord
with a lower current capacity is used, overheating
may occur. Take precautions to ensure that the
extension cord is not strained, crushed, or placed
on top of other electrical appliances, etc.
9. Always unplug the machine when not in use. Ne-
ver pull on the cord to unplug.
10. To reduce the risk of fire, do not use the machine
near gallons or other easily flammable objects.
11. Place the machine in a ventilated place, keep in
mind that the operation of the machine is internal
combustion.
12. Try to tie up your hair and avoid wearing loose
clothing and any hanging objects.
13. To avoid electrocution, never work on wet sur-
faces.
14. Always wear protective goggles. Please note that
glasses for vision correction are not protective
goggles.
ASSEMBLY
1. Remove all parts from the packaging and ensure
that they are not in poor condition.
2. Remove the parts that come inside the machine.
3. Place clean cardboard on the floor and lay the
machine on its lid. (Make sure you keep the co-
ver closed when laying the machine on its lid).
4. Mount four legs on brackets with M6x12 Phillips
screws and M6 nuts. Note: do not tighten too
much.
5. Place the platform between the legs with the flat
surface facing down and attach to the legs with
M6x12 Phillips screws and M6 nuts M6.
6. With the legs tight against the bottom shelf, tigh-
ten all bottom shelf screws.
7. Tighten all screws installed in step 4.
8. Stand machine up; be careful to keep lid closed.
9. Place work platform and basket on machine.
10. Mount the pump assembly in the slot on the side
of the machine. Place the filter strainer in posi-
tion.
11. Connect the machine to 220v 50hz standard soc-
ket and fill liquid with the appropriate amount.
12. Turn the power switch on, liquid should not flow
from the flexible tap.
TROUBLE SHOOTING
The only trouble you could ever experience with your
parts washer is reduced volume flow or no flow of cle-
aning liquid from the flex hose nozzle. The probable
cause is foreign matter in the flex hose.
POSSIBLE SOLUTIONS:
1. Check that indicator light on switch box is lit.
2. Using an insulated handle screw driver to lightly
touch tip of housing of motor. A light oscillation
magnetic pull indicates power is reaching the
motor.
3. Disconnect power plug, remove flex hose from
pump flow - out line.
4. Remove front of pump housing by removing 3
screws. Clear any foreign matter lodged around
impeller.
5. Resemble in reverse order.
TECHNICAL SPECIFICATIONS
Tank capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150L
Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25L
Inner measures deposit . . . . . . . . 1060x490x270mm
Total machine measures. . . . . . . . . 1090x520x890mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 kg
· 3 ·