Manual Tuning - Audizio ARLES Micro HiFi System Bedienungsanleitung

FULL SCAN
The full scan will search for the entire DAB+ Band III channels. After the scan has finished, the first alphanumerically found
station will be automatically selected.
1. To activate auto scan, press the SCAN/
bar will be shown on display.
2. All the stations that have been found will be stored automatically. To explore and listen to the found stations, press the
or buttons to select. Then press ENTER to confirm.

MANUAL TUNING

As well as the auto tune function, you can opt to perform a manual tune. This can help you when aligning your aerial or when
adding stations that were missed during auto tuning.
1. In DAB mode, press MENU on the remote control to display the menu.
2. Press the or buttons to select MANUAL TUNE, confirm by pressing ENTER.
3. Press the or buttons to cycle through the DAB/DAB+ channels, which are numbered
from 5A to 13F.
4. After your desired channel number is selected, press the ENTER button to confirm. The
display will show the multiplex.
5. Press the MENU button again to add the selected channel to the station list.
DRC (DYNAMIC RANGE COMPRESSION)
If you are listening to music with high dynamic range in a noisy environment, you may wish to compress the audio dynamic
range:
1. In DAB mode, press MENU on the remote control to display the menu.
2. Press the or buttons to select "DRC" and then press ENTER on the remote control to confirm.
3. Press or to select off / high / low. Press ENTER on the remote control to confirm.
PRUNE
To remove all unavailable stations from the list (prune):
1. In DAB mode, press MENU on the remote control to display the menu.
2. Press or to select "Prune" and press ENTER on the remote control to confirm.
3. Press or to select <YES> and press ENTER on the remote control to delete the unavailable stations.
4. You can press or
SECONDARY SERVICES
You may see a ">" symbol after the name of the station, this indicates that there are secondary services available for that
particular station. This means the station contains extra services that are related to the primary station (e.g. a sports station
has added additional commentaries). The secondary services are stated directly after the primary station in the station list.
To select the secondary station, press the MENU button when the ">" appears in the display before the station name. When
the secondary service ends, the unit will automatically switch back to the primary station.
PRESET STATIONS
NOTE: The following is only functional by using the remote control.
1. Press and hold the MEMORY button. The display will show "Preset Store < 1:(Empty)>".
2. Press or to select your desired preset station number. Then press the ENTER button to confirm.
3. The station will be stored in a few seconds, the display will show "Preset # Stored".
RECALLING A STORED STATION
NOTE: The following is only functional by using the remote control.
1. Once you have saved a station to one of the preset buttons, you can recall it by pressing the MEMORY button.
2. Press or until your desired station shows on the display; press ENTER to confirm.
Press INFO on the device, the display will switch between multiple display modes. The information of each display mode is
displayed on the lower segment of the display.
SIGNAL STRENGTH
The display will show a bar to indicate the signal strength. The stronger the signal, the longer the bar will be
from left to right.
PROGRAMME TYPE
This describes the "style" or "genre" of the program that is being broadcasted.
ENSEMBLE
This displays the name of the multiplex that contains the station you are listening to. A multiplex is a
collection of radio stations that is bundled and transmitted on one single frequency. There are national and
local multiplexes. Local ones contain stations that are specific to that area.
NOTE: DAB (+), unlike normal radio, groups together several stations and transmits them on one frequency.
FREQUENCY
This displays the frequency of the present station, such as "11C 220.352MHz".
SIGNAL ERROR
This displays a number showing the error rate. If the number is 0, it means the signal received is error free and
the signal strength is strong. If the error rate is high, it is recommended to reposition the aerial or unit.
button and "Scanning ..." and a progressing slide
to select <NO>, then press ENTER on the remote control to cancel.
7